Juniper Networks JUNOS OS 10.4 User Manual
Junos
Table of contents
Document Outline
- Abbreviated Table of Contents
- Table of Contents
- List of Figures
- List of Tables
- About This Guide
- Part 1: Overview
- Chapter 1: Overview of Ethernet Solutions
- Ethernet Terms and Acronyms
- Networking and Internetworking with Bridges and Routers
- Network Addressing at Layer 2 and Layer 3
- Networking at Layer 2: Benefits of Ethernet Frames
- Networking at Layer 2: Challenges of Ethernet MAC Addresses
- Networking at Layer 2: Forwarding VLAN Tagged Frames
- Networking at Layer 2: Forwarding Dual-Tagged Frames
- Networking at Layer 2: Logical Interface Types
- A Metro Ethernet Network with MX Series Routers
- Layer 2 Networking Standards
- Chapter 1: Overview of Ethernet Solutions
- Part 2: Basic Solutions for MX Series Routers
- Chapter 2: Basic Layer 2 Features on MX Series Routers
- Layer 2 Features for a Bridging Environment
- Example Roadmap: Configuring a Basic Bridge Domain Environment
- Example Step: Configuring Interfaces and VLAN Tags
- Example Step: Configuring Bridge Domains
- Example Step: Configuring Spanning Tree Protocols
- Example Step: Configuring Integrated Bridging and Routing
- Chapter 3: Virtual Switches
- Chapter 4: VLANs Within Bridge Domain and VPLS Environments
- VLANs Within a Bridge Domain or VPLS Instance
- Packet Flow Through a Bridged Network with Normalized VLANs
- Configuring a Normalized VLAN for Translation or Tagging
- Configuring Learning Domains for VLAN IDs Bound to Logical Interfaces
- Example: Configuring a Provider Bridge Network with Normalized VLAN Tags
- Example: Configuring a Provider VPLS Network with Normalized VLAN Tags
- Example: Configuring One VPLS Instance for Several VLANs
- Chapter 5: Bulk Administration of Layer 2 Features on MX Series Routers
- Chapter 6: Dynamic Profiles for VLAN Interfaces and Protocols
- Chapter 7: MX Series Router as a DHCP Relay Agent
- Chapter 8: MX Series Router in an ATM Ethernet Interworking Function
- Chapter 2: Basic Layer 2 Features on MX Series Routers
- Part 3: Ethernet Filtering, Monitoring, and Fault Management Solutions for MX Series Routers
- Chapter 9: Layer 2 Firewall Filters
- Firewall Filters for Bridge Domains and VPLS Instances
- Example: Configuring Policing and Marking of Traffic Entering a VPLS Core
- Example: Configuring Filtering of Frames by MAC Address
- Example: Configuring Filtering of Frames by IEEE 802.1p Bits
- Example: Configuring Filtering of Frames by Packet Loss Priority
- Chapter 10: IEEE 802.1ag OAM Connectivity-Fault Management
- Chapter 11: ITU-T Y.1731 Ethernet Frame Delay Measurements
- Ethernet Frame Delay Measurements
- Configuring MEP Interfaces to Support Ethernet Frame Delay Measurements
- Triggering an Ethernet Frame Delay Measurements Session
- Viewing Ethernet Frame Delay Measurements Statistics
- Example: Configuring One-Way Ethernet Frame Delay Measurements with Single-Tagged Interfaces
- Example: Configuring Two-Way Ethernet Frame Delay Measurements with Single-Tagged Interfaces
- Example: Configuring Ethernet Frame Delay Measurements with Untagged Interfaces
- Chapter 12: IEEE 802.3ah OAM Link-Fault Management
- Chapter 13: Ethernet Ring Protection
- Ethernet Ring Protection
- Ethernet Ring Protection Using Ring Instances for Load Balancing
- Example: Configuring Ethernet Ring Protection for MX Series Routers
- Example: Configuring Load Balancing Within Ethernet Ring Protection for MX Series Routers
- Requirements
- Overview and Topology
- Configuration
- Verification
- Verifying the Ethernet Protection Ring on CS1
- Verifying the Data Channel CS1
- Verifying the VLANs on CS1
- Verifying the Ethernet Protection Ring on CS2
- Verifying the Data Channel CS2
- Verifying the VLANs on CS2
- Verifying the Ethernet Protection Ring on AS1
- Verifying the Data Channels on AS1
- Verifying the VLANs on AS1
- Example: Viewing Ethernet Ring Protection Status—Normal Ring Operation
- Example: Viewing Ethernet Ring Protection Status—Ring Failure Condition
- Chapter 9: Layer 2 Firewall Filters
- Index: Index