FUJITSU C150-E049-02EN User Manual
M3099gx/gh image scanner oem manual
Table of contents
Document Outline
- M3099GX/GH IMAGE SCANNER OEM MANUAL
- Preface
- Conventions
- Contents
- OVERVIEW
- Scanner Types
- Features
- Configuration
- Operation Overview
- SPECIFICATIONS
- General
- Electrical Specifications
- Environmental Specifications
- Physical Specifications
- Option Specifications
- INTERFACE
- Physical
Specifications
- SCSI Bus (See ANSI SCSI-2 4.5)
- SCSI Bus Signals (See ANSI SCSI-2 4.6)
- Signal Values
- Signal Source
- SCSI Bus Timing
- Arbitration Delay
- Assertion period
- Bus Clear Delay
- Bus Free Delay
- Bus Set Delay
- Bus Settle Delay
- Cable Skew Delay
- Data Release Delay
- Deskew Delay
- Disconnection Delay
- Hold Time
- Negation Period
- Power-On to Selection Time
- Reset to Selection Time
- Reset Hold Time
- Selection Abort Time
- Selection Time-out Delay
- Transfer Period
- SCSI Bus Phases
- SCSI Bus Conditions
- SCSI Bus Phases Sequences
- Commands (See
ANSI SCSI-2 7)
- RESERVE UNIT Command
- RELEASE UNIT Command
- TEST UNIT READY Command
- INQUIRY Command (See ANSI SCSI-2 7.2.5)
- REQUEST SENSE Command (See ANSI SCSI-2 8.2.14)
- SEND DIAGNOSTIC Command
- SET WINDOW Command
- OBJECT POSITION
- SEND Command
- SCAN Command
- READ Command
- MODE SELECT(6) Command
- MODE SENSE(6) Command
- ENDORSER Command (ENDORSER option is required)
- Status (See ANSI SCSI-2 7.3)
- Message(See
ANSI SCSI-2 6.5)
- ABORT (Init Æ Targ)
- BUS DEVICE RESET (Init Æ Targ)
- COMMAND COMPLETE (Init ¨ Targ)
- DISCONNECT (Init ¨ Targ)
- IDENTIFY (Init Æ Targ)
- INITIATOR DETECTED ERROR (Init Æ Targ)
- MESSAGE PARITY ERROR (Init Æ Targ)
- MESSAGE REJECT (Init ´ Targ)
- NO OPERATION (Init Æ Targ)
- RESTORE POINTERS (Init ¨ Targ)
- SAVE DATA POINTER (Init ¨ Targ)
- SYNCHRONOUS DATA TRANSFER REQUEST
- Command Sequence
- BASIC OPERATION
- Power Switch Operation
- Opening the Upper Transport Unit
- Closing the Upper Transport Unit
- Operator Panel
- Loading Document
- Lamp Replacement
- Roller ASY Replacement
- Pick Roller Replacement
- Belt Replacement
- Pad Replacement
- ERROR PROCESSING AND RECOVERY
- Device and Operator Actions for Temporary Errors
- Device and Operator Actions for Equipment Errors
- DOCUMENT SPECIFICATION
- Document Size
- Document Quality
- Document Limitations
- Grounding Color Area
- Drop-out Color
- Job Separation Sheet
- CONSUMABLES AND ACCESSORIES
- Consumables
- Accessories
- CLEANING
- Cleaning Locations and Frequencies
- Cleaning Tools
- Procedure
- ENDORSER
- A1. Specifications
- A2. Panel operation
- A3. Print head handling
- SETUP MODE
- B.1 Activating the setup mode
- B.2 Operational transition in the setup mode
- B.3 Contents of
the setup
mode
- B3.1 Setting double-feed detection
- B3.2 Setting IPC-2 pre-set mode
- B3.3 Reset of abrasion counter
- B3.4 Setting buzzer
- B3.5 Setting pre-pick
- B3.6 Adjusting LCD contrast
- B3.7 Setting pick speed
- B3.8 Setting initial value of endorser
- B3.9 Setting reset method of endorser
- B3.10 Reset of endorser
- B3.11 Reset of ink counter
- B3.12 Setting SCSI-ID
- B3.13 Setting Product-ID
- B3.14 Setting picking start time
- B3.15 Setting picking time
- B3.16 Setting time-out limit
- B3.17 Setting hopper time
- B3.18 Setting heater control
- SEPARATION PRESSURE ADJUSTMENT
- Glossary of Terms
- Index
- Reader Comment Form