Beko 30 Inch Over the Range Convection Microwave Installation Guide - Manual (Page 54)

Four à micro-ondes à convection à hotte intégrée / Manuel d’installation 54 / 63 FR
5 Installation
5.2.2 Évacuation à l’extérieur par
l’arrière (conduit horizontal de
type B)
3/8" TO EDGE
NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIO NS IN THE INSTALLATION INSTRU CTIONS BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom mounting plate and to locate the h orizontal exhaust outlet. 1. Use a level to check that the templa te is positioned accurately. 2. Locate and mark at least one st ud on the left or right side of the centerline. It is important to use at least one wo od screw mounted firmly in a stud to sup port the weight of the microwave. Mark two addition al, evenly spaced locations for the supplied toggle bo lts. 3. Drill holes in the marked locatio ns. Where there is a stud, drill a 3/16" hole for woo d screws. For holes that do not line up with a stud, d rill 5/8" holes for toggle bolts. DO NOT INSTALL THE MOUNTIN G PLATE AT THIS TIME. 4. Remove the template from the r ear wall. 5. Revie h t w e Installation Instruction book for your installation situation.
Locate and mark holes to align wi th holes in the mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTERLINE. MARK THE LOCATION FOR 2 ADDI TIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MO UNTING PLATE
AREA. Locate and mark holes to align w ith holes in the . e t a l p g n it n u o m IMPORTANT: LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTERLINE. MARK THE LOCATION FOR 2 ADD ITIONAL, EVENLY SPACED TOGGLE BOLTS IN THE MOUNTING PLATE AREA. Trim the rear wall template along the dotted line.
Trim the rear wall template al ong the dotted line.
12"
4"
Darle vuelta a la hoja para cons ultar la versión en Español.
Vue d’ensemble de l’installation
B1. Préparation du mur arrière
B2. Retrait de la plaque du ventilateur
B3. Fixation de la plaque de montage au mur
B4. Préparation de l’armoire supérieure
B5. Ajustement du ventilateur
B6. Installation du four à micro-ondes
A
Assurez-vous que les vis du moteur
du ventilateur et de la plaque du
ventilateur sont correctement ser-
rées lorsque vous les remettez en
place. Cela permet d’éviter des vibra-
tions excessives.
A
Assurez-vous que le câblage du mo-
teur a été effectué et correctement
fixé, et que les câbles ne sont pas
coincés.
B1. Préparation du mur arrière pour
l’évacuation à l’extérieur par l’arrière
Vous devez percer une ouverture dans le mur ar-
rière pour l’évacuation à l’extérieur.
3/8" TO EDGE
NOTE: IT IS VE RY IMPOR TANT TO READ AND FOLL OW THE DIRECTI ONS IN THE INSTA L S N I N O I T A L TRUCTIONS BEFORE PR OCEEDING WI TH THIS REAR WALL TEMP LATE. This Rear Wall Te mplate serves to p osition the bottom mounting plate and to locate the horiz ontal exhaust outlet. 1. Use a level to ch eck that the templa te is positioned accurately. 2. Locate and mar k at least one stud on the left or right side of the ce nterline. It is important to us e at least one woo d screw mounted firmly in a stud to support the weight of the microwave. Mark two additiona l, evenly spaced locations for the supplied toggle bolts. 3. Drill holes in the marked locations . Where there is a stud, drill a 3/16" hole for wood screws. For holes that do not line up with a stud, drill 5/8 " holes for toggle bolts. DO NOT INSTALL THE MOUNT ING PLATE AT THIS TIME. 4. Remove the tem plate from the rear wall. 5. Review the Ins tallation Instruction book for your installation situatio n.
Locate and mar k holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEAST ON E STUD ON EITH ER SIDE OF THE CENTERLINE . MARK THE LOC ATION FOR 2 ADDITIONAL , EVENLY
SPACED TOGG LE BOLTS IN THE MOUNTIN G PLATE
AREA.
Locate and mar k holes to align w ith holes in the mounting plate. IMPORTA NT: LOCATE AT LE AST ONE STUD O N EITHER SI DE OF
THE CENTER LINE. MARK TH E LOCATION FOR 2 ADDITIONAL , EVENLY SPACED TOGG LE BOLTS IN THE MOUNTI NG PLATE AREA.
Trim the rear wa ll template along the d otted line.
Trim the rear wall template along the dotted line.
12"
4"
Darle vuelta a la hoja para consul tar la versión en Españ ol.
• Lisez les instructions relatives au GABARIT
POUR MUR ARRIÈRE.
• Collez-le au mur arrière avec du ruban adhésif,
en l’alignant sur les trous préalablement percés
pour les trous A et B de la plaque de montage.
• Percez l’ouverture conformément aux
instructions sur le GABARIT POUR MUR ARRIÈRE.