Beko 30 Inch Over the Range Convection Microwave Installation Guide - Manual (Page 46)

Four à micro-ondes à convection à hotte intégrée / Manuel d’installation 46 / 63 FR
5 Installation
5.1.3 Établissement de l’emplacement
de la plaque murale sous votre armoire
16-1/2
Àt least 30
CL
3/8" TO EDGE
NOTE: IT IS VER Y IMPORTANT TO READ AND FOLLO W THE DIRECTIO NS IN THE INSTALLA TION INSTRUCT IONS BEFORE PROC EEDING WITH TH IS REAR WALL TEM PLATE. This Rear Wall Tem plate serves to posit ion the bottom mounting plate and to locate the horizo ntal exhaust outlet. 1. Use a level to che ck that the template is positioned accurately. 2. Locate and mark at least one stud on the left or right side of the ce nterline. It is important to use at least one wood screw mounted firm ly in a stud to suppo rt the weight of the microwave. M ark two additional, e venly spaced locations for the sup plied toggle bolts. 3. Drill holes in the marked locations. W here there is a stud, drill a 3/16" hole for wood screw s. For holes that do not line up w ith a stud, drill 5/8" h oles for toggle bolts. DO NOT INSTALL THE MOUNTING P LATE AT THIS TIME. 4. Remove the tem plate from the rear w all. 5. Review the Install ation Instruction boo k for your installation situation .
Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEA ST ONE STUD ON EITHER SIDE OF THE CENTERLIN E. MARK THE LOC ATION FOR 2 AD DITIONAL, EVEN LY SPACED TOGGL E BOLTS IN TH E MOUNTING PL ATE AREA.
Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEA ST ONE STUD ON EITHER SIDE OF THE CENTERLIN E. MARK THE LOCAT ION FOR 2 ADDIT IONAL, EVENLY SPACED TOGG LE BOLTS IN TH E MOUNTING PLA TE AREA.
Trim the rear wall template along th e dotted line.
Trim the rear wa ll template along the dotted line.
12"
4"
Darle vuelta a la ho ja para consultarla versión en Españo l.
Tracez une ligne verticale sur le mur au centre de
l'espace de 30 po de large. Collez le gabarit pour
mur arrière sur le mur le long de la ligne centrale
et en touchant le bas de l'armoire.
Emplacement de la plaque—sous une armoire
à fond plat
ʺ
À 33 po de la surface de cuisson
Tracez une ligne verticale sur le mur au centre de
l'espace de 30 po de large.
Collez le gabarit pour mur arrière sur le mur le long de la
ligne centrale et en touchant le cadre de l'armoire inférieure.
CL
3/8" TO EDGE
NOTE: IT IS VER Y IMPORTANT T O READ AND FOLL OW THE DIRECT IONS IN THE INSTALL ATION INSTRUC TIONS BEFORE PROCE EDING WITH TH IS REAR WALL TEM PLATE. This Rear Wall Tem plate serves to posit ion the bottom mounting plate and to locate the horizon tal exhaust outlet. 1. Use a level to che ck that the template is positioned accurately. 2. Locate and mark at least one stud on the left or right side of the cen terline. It is important to use at least one wood screw mounted firm ly in a stud to suppo rt the weight of the microwave. M ark two additional, e venly spaced locations for the su pplied toggle bolts. 3. Drill holes in the marked locations. W here there is a stud, drill a 3/16 " hole for wood scre ws. For holes that do not line up with a stud, drill 5/8" holes for toggle bolts. DO NOT INSTALL THE MOUNTING PL ATE AT THIS TIME. 4. Remove the tem plate from the rear w all. 5. Review the Install ation Instruction boo k for your installation situation .
Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEA ST ONE STUD ON EITHER SIDE OF THE CENTERLIN E. MARK THE LOC ATION FOR 2 AD DITIONAL, EVE NLY SPACED TOGGL E BOLTS IN THE MOUNTING PLAT E AREA.
Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEA ST ONE STUD ON EITHER SIDE OF THE CENTERLIN E. MARK THE LOC ATION FOR 2 AD DITIONAL, EVEN LY SPACED TOGGLE BOLTS IN THE M OUNTING PLATE AREA.
Trim the rear wall template along t he dotted line.
Trim the rear wa ll template along the dotted line.
12"
4"
Darle vuelta a la h oja para consultar la versión en Españo l.
Emplacement de la plaque—sous une armoire dotée d'un
rebord
Tracez une ligne sur le mur
arrière correspondant à la
profondeur du surplomb
avant.
À 33 po de la surface de cuisson
CL
3/8" TO EDGE
NOTE: IT IS VER Y IMPORTANT T O READ AND FOL LOW THE DIRE CTIONS IN THE INSTALL ATION INSTRUC TIONS BEFORE PROC EEDING WITH T HIS REAR WALL TE MPLATE. This Rear Wall Te mplate serves to p osition the bottom mounting plate and to locate the horizo ntal exhaust outlet. 1. Use a level to ch eck that the templa te is positioned accurately. 2. Locate and mark at least one stud o n the left or right side of the ce nterline. It is important to us e at least one woo d screw mounted firm ly in a stud to supp ort the weight of the microwave. Mark two additiona l, evenly spaced locations for the su pplied toggle bolts . 3. Drill holes in the marked locations. Where there is a stud, drill a 3/16" hole for wood scre ws. For holes that do not line up with a stud, drill 5/8 " holes for toggle bolts. DO NOT INSTALL THE MOUNTING PLATE AT THIS TIME. 4. Remove the tem plate from the rear wall. 5. Review the Insta llation Instruction book for your installation situatio n.
Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEA ST ONE STUD ON EITHER SID E OF THE CENTERLIN E. MARK THE LOC ATION FOR 2 A DDITIONAL, EV ENLY SPACED TOGG LE BOLTS IN TH E MOUNTING P LATE AREA.
Locate and mark holes to align with holes in the mounting plate. IMPORTANT: LOCATE AT LEA ST ONE STUD O N EITHER SIDE OF THE CENTERLIN E. MARK THE LOC ATION FOR 2 A DDITIONAL, EV ENLY SPACED TOGG LE BOLTS IN TH E MOUNTING P LATE AREA.
Trim the rear w all template alon g the dotted lin e.
Trim the rear w all template alo ng the dotted lin e.
12" 4"
Darle vuelta a la hoja para consult ar la versión en Españ ol.
3/8" TO EDGE
NOTE: IT IS VER Y IMPORTANT TO READ AND FO LLOW THE DIR ECTIONS IN THE INSTALL ATION INSTR UCTIONS BEFORE PROC EEDING WITH T HIS REAR WALL TE MPLATE. This Rear Wall Te mplate serves to p osition the bottom mounting plate and to locate the horizo ntal exhaust outlet. 1. Use a level to chec k that the template is positioned accurately. 2. Locate and mark at least one stud o n the left or right side of the c enterline. It is important to us e at least one woo d screw mounted firml y in a stud to suppo rt the weight of the microwave. Ma rk two additional, e venly spaced locations for the sup plied toggle bolts. 3. Drill holes in the marked locations. W here there is a stud, drill a 3/1 6" hole for wood scr ews. For holes that do not line u p with a stud, drill 5 /8" holes for toggle bolts. DO NOT INSTALL THE MOUNTING PLATE AT THIS TIME. 4. Remove the temp late from the rear w all. 5. Review the Insta llation Instruction book for your installation situa tion.
Locate and ma rk holes to align w ith holes in the mounting plate. IMPORTANT: LOCATE AT LEAST ONE STUD ON E ITHER SIDE OF THE CENTERLIN E. MARK THE LOCATIO N FOR 2 ADDIT IONAL, EVENLY SPACED TOGG LE BOLTS IN TH E MOUNTING P LATE AREA.
Locate and ma rk holes to align w ith holes in the mounting plate. IMPORTANT: LOCATE AT LEAST ONE ST UD ON EITHER SIDE OF THE CENTERLIN E. MARK THE LOC ATION FOR 2 AD DITIONAL, EVEN LY SPACED TOGG LE BOLTS IN TH E MOUNTING P L AREA.
Trim the rear w all template along the dotted line.
Trim the rear w all template along the dotted line .
12"
4"
Darle vuelta a la hoja para consul tar la versión en Españ ol.
Emplacement de la plaque—sous une armoire
dont le fond est doté d’un surplomb avant
Vos armoires peuvent être dotées de garnitures
décoratives qui entravent l’installation du micro-
ondes. Enlevez l’élément décoratif pour installer
convenablement le four à micro-ondes et pour
vous assurer qu’il est à niveau
Le four à micro-ondes doit être à ni-
veau.
Utilisez un niveau pour vous assurer que le fond de
l’armoire est à niveau.
Si les armoires sont dotées uniquement d’un re-
bord avant, sans rebord sur les côtés ou à l’arrière,
installez la plaque de montage plus bas, à la même
distance que le rebord avant de l’armoire. Ainsi, le
four sera à niveau.
1. Mesurez l’épaisseur intérieure du rebord avant
de l’armoire.
2. Tracez une ligne horizontale sur le mur arrière,
en dessous du fond de l’armoire, à une distance
égale à l’épaisseur intérieure du rebord avant de
l’armoire.
3. Pour l’installation sous une armoire dotée
uniquement d’un rebord avant, alignez les
languettes de montage avec cette ligne
horizontale, sans toucher le fond de l’armoire,
tel que décrit dans le sous-titre 5.1.4.