KEPCO KLR Series Developers Guide - Manual (Page 5)

KLR DEVGD 020498
iii
TABLE OF CONTENTS
SECTION PAGE
SECTION 7 - IEEE 488.2 (GPIB) INTERFACE
7.2 IEEE 488 (GPIB) Bus Protocol ................................................................................................................... 7-1
7.2.1 Changing the GPIB Address ................................................................................................................... 7-3
SECTION 8 - RS 232C INTERFACE [STANDARD MODELS ONLY]
8.2 RS232-C Operation [Standard Models Only].............................................................................................. 8-1
8.2.1 RS 232 Implementation [Standard Models Only] .................................................................................... 8-1
8.2.2 Data Transfer Protocols [Standard Models Only].................................................................................... 8-2
8.2.2.1 Echo Mode [Standard Models Only] .................................................................................................. 8-3
8.2.2.2 Prompt Method [Standard Models Only] ............................................................................................ 8-3
8.2.2.3 XON XOFF Method [Standard Models Only] ..................................................................................... 8-3
8.2.2.4 Isolating RS 232 Communications Problems [Standard Models Only] .............................................. 8-4
SECTION 9 - LAN INTERFACE [E-Series MODELS ONLY]
9.2 Using Port 80 (Web Interface) .................................................................................................................... 9-1
9.3 Using Port 5024 (Telnet)............................................................................................................................. 9-1
9.4 Using Port 5025 (SCPI-RAW)..................................................................................................................... 9-2
9.5 Using Port 1024 (VXI-11)............................................................................................................................ 9-2
9.6 Using Port 5044 ( *TRG command)............................................................................................................ 9-2
9.7 SUNRPC Port 111 ...................................................................................................................................... 9-2
APPENDIX A - IEEE 488.2 COMMAND/QUERY DEFINITIONS
A.2 *CLS — Clear Status Command ............................................................................................................... A-1
A.3 *ESE — Standard Event Status Enable Command................................................................................... A-1
A.4 *ESE? — Standard Event Status Enable Query........................................................................................ A-2
A.5 *ESR? — Event Status Register Query..................................................................................................... A-2
A.6 *IDN? — Identification Query..................................................................................................................... A-2
A.7 *OPC — Operation Complete Command .................................................................................................. A-3
A.8 *OPC? — Operation Complete Query ....................................................................................................... A-3
A.9 *OPT? — Operation Complete Query ....................................................................................................... A-4
A.10 *RCL — Recall Command ......................................................................................................................... A-4
A.11 *RST — Reset Command.......................................................................................................................... A-4
A.12 *SAV — Save Command........................................................................................................................... A-4
A.13 *SRE — Service Request Enable Command ............................................................................................ A-5
A.14 *SRE? — Service Request Enable Query ................................................................................................. A-6
A.15 *STB? — Status Byte Register Query ....................................................................................................... A-6
A.16 *TRG — Trigger Command ....................................................................................................................... A-6
A.17 *TST? — Self Test Query .......................................................................................................................... A-6
A.18 *WAI — Wait Command ............................................................................................................................ A-6
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 Introduction ................................................................................................................................................ B-1
B.2 Numerical Values....................................................................................................................................... B-2
B.3 ABOR t Command...................................................................................................................................... B-2
B.4 CAL ibrate Commands and Queries .......................................................................................................... B-2
B.5 DISP lay[:Window]:TEXT[:DATA]? Query.................................................................................................. B-2
B.6 INIT iate[:IMMediate] Command ................................................................................................................ B-2
B.7 INIT iate:CONTinuous Command .............................................................................................................. B-3
B.8 INIT iate:CONTinuous Query ..................................................................................................................... B-4
B.9 [SOUR ce:]LIST:CLEar Command............................................................................................................. B-4
B.10 [SOUR ce:]LIST:CONTrol Command......................................................................................................... B-4
B.11 [SOUR ce:]LIST:CONTrol? QUERY........................................................................................................... B-4
B.12 [SOUR ce:]LIST:CONtrol:POINts? Query.................................................................................................. B-4