KEPCO KLP Series Developer's Guide, Rev 1 - Manual (Page 5)

KLP SVC 020498
iii
TABLE OF CONTENTS
SECTION PAGE
6.5.7 Root Specifier......................................................................................................................................... C-5
6.5.8 Message Terminator .............................................................................................................................. C-5
6.6 Understanding The Command Structure ................................................................................................... C-7
6.7 Program Message Syntax Summary ......................................................................................................... C-7
6.7.1 Exceptions to the Rules.......................................................................................................................... C-8
6.8 Programming Examples ............................................................................................................................ C-8
SECTION 7 - IEEE 488.2 (GPIB) INTERFACE
7.2 IEEE 488 (GPIB) Bus Protocol .................................................................................................................. D-1
7.2.1 Changing the GPIB Address .................................................................................................................. D-3
SECTION 8 - RS 232C INTERFACE [-1200 MODELS ONLY]
8.2 RS232-C Operation [-1200 Models Only] .................................................................................................. E-1
8.2.1 Serial Interface [-1200 Models Only] ...................................................................................................... E-2
8.2.2 RS 232 Implementation [-1200 Models Only]......................................................................................... E-2
8.2.2.1 Echo Mode [-1200 Models Only]....................................................................................................... E-3
8.2.2.2 Prompt Method [-1200 Models Only] ................................................................................................ E-3
8.2.2.3 XON XOFF Method [-1200 Models Only].......................................................................................... E-3
8.2.2.4 Isolating RS 232 Communications Problems [-1200 Models Only]................................................... E-4
SECTION 9 - LAN INTERFACE [-1.2K MODELS ONLY]
9.2 Using Port 80 (Web Interface) ................................................................................................................... F-1
9.3 Using Port 5024 (Telnet)............................................................................................................................ F-1
9.4 Using Port 5025 (SCPI-RAW).................................................................................................................... F-1
9.5 Using Port 1024 (VXI-11)........................................................................................................................... F-2
9.6 Using Port 5044 ( *TRG command)........................................................................................................... F-2
9.7 SUNRPC Port 111 ..................................................................................................................................... F-2
APPENDIX A - IEEE 488.2 COMMAND/QUERY DEFINITIONS
A.2 *CLS — Clear Status Command ............................................................................................................... A-1
A.3 *ESE — Standard Event Status Enable Command................................................................................... A-1
A.4 *ESE? — Standard Event Status Enable Query........................................................................................ A-2
A.5 *ESR? — Event Status Register Query..................................................................................................... A-2
A.6 *IDN? — Identification Query..................................................................................................................... A-2
A.7 *OPC — Operation Complete Command .................................................................................................. A-2
A.8 *OPC? — Operation Complete Query ....................................................................................................... A-3
A.9 *RCL — Recall Command ......................................................................................................................... A-4
A.10 *RST — Reset Command.......................................................................................................................... A-4
A.11 *SAV — Save Command........................................................................................................................... A-4
A.12 *SRE — Service Request Enable Command ............................................................................................ A-4
A.13 *SRE? — Service Request Enable Query ................................................................................................. A-5
A.14 *STB? — Status Byte Register Query ....................................................................................................... A-5
A.15 *TRG — Trigger Command ....................................................................................................................... A-5
A.16 *TST? — Self Test Query .......................................................................................................................... A-5
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 Introduction ................................................................................................................................................ B-1
B.2 Numerical Values....................................................................................................................................... B-2
B.3 ABOR t Command...................................................................................................................................... B-2
B.4 CAL ibrate Commands and Queries .......................................................................................................... B-2
B.5 DISP lay [:Wind ow ]:TEXT[:DATA]? Query.................................................................................................. B-2
B.6 INIT iate Command .................................................................................................................................... B-2
B.7 INIT iate :IMM ediate Command .................................................................................................................. B-3