KEPCO KLP Series Developer's Guide, Rev 1 - Manual (Page 126)

B-20
KLP 031113
B.82 SYSTem:COMMunication:SERial:BAUD COMMAND
SYST:COMM:SER:BAUD
[-1200 MODELS ONLY]
Syntax: Short Form: SYST:COMM:SER:BAUD {38400 | 19200 | 9600 | 4800 | 2400}
Long Form: SYSTem:COMMunication:SERial:BAUD {38400 | 19200 | 9600 | 4800 | 2400}
Description: Sets the unit to operate at the specified baud rate. Factory default is 38400.
B.83 SYSTem:COMMunication:SERial:BAUD? QUERY
SYST:COMM:SER:BAUD?
[-1200 MODELS ONLY]
Syntax: Short Form: SYST:COMM:SER:BAUD?
Long Form: SYSTem:COMMunication:SERial:BAUD?
Return Value: {38400 | 19200 | 9600 | 4800 | 2400}
Description: Indicates baud rate.
B.84 SYSTem:COMMunication:SERial:ECHO COMMAND
SYST:COMM:SER:ECHO
[-1200 MODELS ONLY]
Syntax: Short Form: SYST:COMM:SER:ECHO {1 | 0} (1 = on, enabled, 0 = off, disabled)
Long Form: SYSTem:COMMunication:SERial:ECHO {1 | 0} (1 = on, enabled, 0 = off, disabled)
Description: Enables (1 = ON) or disables (0 = OFF) echo mode (see PAR. 8.2.2.1). When echo mode is ON
causes all subsequent characters to be echoed back. When echo mode is OFF, turns off the character
echo after the nest line terminator character. The *RST command has no effect on echo status
B.85 SYSTem:COMMunication:SERial:ECHO? QUERY
SYST:COMM:SER:ECHO?
[-1200 MODELS ONLY]\
Syntax: Short Form: SYST:COMM:SER:ECHO?
Long Form: SYSTem:COMMunication:SERial:ECHO?
Return Value: (01
H
= on, enabled or 00
H
= off, disabled)
Description: Indicates whether echo mode is on (01
H
) or off (00
H
). (See PAR. 8.2.2.1.)
B.86 SYSTem:COMMunication:SERial:ENABle COMMAND
SYST:COMM:SER:ENAB
[-1200 MODELS ONLY]
Syntax: Short Form: SYST:COMM:SER:ENAB {1 | 0} (1 = on, enabled, 0 = off, disabled)
Long Form: SYSTem:COMMunication:SERial:ENAB {1 | 0} (1 = on, enabled, 0 = off, disabled)
Description: Enables (1 = ON) or disables (0 = OFF) transmission of data via the RS 232 port (see PAR. 8.2.2)
Once RS 232 transmission has been disabled, it can be enabled again by either turning the unit off,
then on, or by sending SYST:COMM:SER:ENAB 1 via the GPIB port.
B.87 SYSTem:COMMunication:SERial:ENABle? QUERY
SYST:COMM:SER:ENAB?
[-1200 MODELS ONLY]
Syntax: Short Form: SYST:COMM:SER:ENAB?
Long Form: SYSTem:COMMunication:SERial:ENAB?
Return Value: (01
H
= on, enabled or 00
H
= off, disabled)
Description: Indicates whether RS 232 transmission mode is enabled (01
H
= ON) or disabled (00
H
= OFF).
(See PAR. 8.2.2.)
B.88 SYST em :COMM unication :SER ial :PACE COMMAND
SYST:COMM:SER:PACE
[-1200 MODELS ONLY]
Syntax: Short Form: SYST:COMM:SER:PACE {NONE | XON}
Long Form: SYSTem:COMMunication:SERial:PACE {NONE | XON}
Description: Enables (XON) or disables (NONE) data flow control via the serial interface (see PAR. 8.2.2.3)
B.89 SYSTem:COMMunication:SERial:PACE? QUERY
SYST:COMM:SER:PACE?
[-1200 MODELS ONLY]
Syntax: Short Form: SYST:COMM:SER:PACE?
Long Form: SYSTem:COMMunication:SERial:PACE?
Return Value: (01
H
= on, XON enabled or 00
H
= off, XON disabled or NONE)
Description: Identifies whether data flow control via the serial interface is enabled (01
H
= XON) or disabled
(00
H
= NONE) (see PAR. 8.2.2.3).