Sealey TA304 - Manual (Page 7)

7. MAINTENANCE
CAPACITANCE
Range Resolution Accuracy
4.000nf 1pf ±5.0% of rdg ± 50dgts
40.00nf 1pf ±5.0% of rdg ± 7dgts
400.0nf 0.1nf
4.000uf 1nf ±3.0% of rdg ± 5dgts
40.00uf 10nf
400.0uf 0.1uf
4.000mf 0.001mf ±10% of rdg ± 10dgts
40.00mf 10.00mf
FREQUENCY
Range Resolution Sensitivity Accuracy
4.000kHz 1Hz
40.00kHz 10Hz >5V rMs ±1.5% of rdg ± 3dgts
400.0kHz 100Hz
4.000MHz 1000Hz
40.00MHz 1kHz >15V rMs ±2.0% of rdg ± 4dgts
DUTY CYCLE
Range Resolution Accuracy
0.5% ~ 99.0% 0.1% ± 2% of rdg ± 5dgts
AUDIBLE CONTINUITY TEST
Audible threshold: < 35Ω
test current: < 1mA Dc typical
PULSE WIDTh
Range Resolution Accuracy
1.0 ~ 20.0ms 0.1ms ± 2% of rdg ± 20dgts
TYPE K TEMPERATURE
Range Resolution Accuracy
-30°c ~ 1000°c 1.0°c ± 3 % of rdg ± 5°c/8°f
-22°f ~ 1832°f 1.0°f (Meter only)
DIODE TEST
Test Current Resolution Accuracy
1.0mA typical 1mV ±5% of rdg ± 15 dgts
open circuit voltage: 3.0V Dc typical
Pulse width: >100us, <100ms
frequency width: 5Hz ~ 100kHz
sensitivity: >5V rMs
 WARNING! Do not attempt to repair or service the analyser unless you are qualified to do so and have the relevant calibration, performance test,
and service information. to avoid electrical shock or damage to the meter do not get water inside the case.
7.1. Periodically wipe the case with a damp cloth and mild detergent. Do not use solvents.
7.2. turn the analyser off when not in use and remove the battery if stored for a long period of time.
7.3. Do not store the analyser in a place of high humidity or high temperature.
7.4. Replacing The Battery
 WARNING! to avoid electric shock, disconnect the test leads from the analyser before removing the battery cover.
7.4.1. When the battery becomes exhausted or drops below the operating voltage, the battery symbol will be appear in the left hand side of the display.
7.4.2. open the battery cover by loosening the two screws using a small cross head screwdriver.
7.4.3. remove the old battery and insert the new one, observing the correct polarity.
7.4.4. replace the battery cover and secure with the two screws.
 WARNING! to avoid electric shock, do not operate the analyser until the battery cover is secured in place.
7.5. Replacing The Fuses
 WARNING! to avoid electric shock, disconnect the test leads from the analyser before accessing the fuses.
7.5.1. open the rear cover by loosening the six screws using a small cross head screwdriver. Gently ease the rear cover off.
7.5.2. remove the old fuse from its holder by gently pulling it out. take care not to touch any other internal parts of the analyser.
7.5.3. Install the new fuse into its holder by gently pushing it in.
note: Always use a fuse of the correct size and value.
Fuse Ratings:
20A/250V, 6.3 x 32mm fast acting ceramic type for the 20A range.
0.5A/250V, 5 x 20mm fast acting ceramic type for the 400mA range.
7.5.4. replace the rear cover and secure with the six screws.
 WARNING! to avoid electric shock, do not use the analyser until it has been fully re-assembled.
Environmental Protection.
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycle
centre and disposed of in a manner which is compatible with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way.
contact your local solid waste authority for recycling information.
Battery Removal.
WARNING! to avoid electric shock, disconnect the test leads from any source of voltage before removing the battery cover.
Disconnect the test leads from the meter.
see section 7.4 for battery removal.
1. remove and dispose of batteries according to local authority guidelines.
2. under the Waste Batteries and Accumulators regulations 2009, Jack sealey Ltd are required to inform potential purchasers of products containing
batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack sealey Ltd’s Batteries
Producer registration number (BPrn) is BPrn00705
8. PARTS
Item Part No. Description
1. tA302.01 tEMPErAturE ProBE
2. tA302.02 InDuctIVE PIcK-uP
Item Part No. Description
3. tA302.03 tEst LEADs
4. tA302.04 WAtEr PLuG
tA304 Issue:4(I) - 17/06/14
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park ,
Bury st. Edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Original Language Version © Jack sealey Limited