Sealey TA201 - Manual

. . . . . . . . . . . . . . . . . . . . . Continuity
BAT . . . . . . . . . . . . . . . . . Low Battery
. . . . . . . . . . . . . . . . . . . . . Diode
DATA HOLD . . . . . . . . . . . Data Hold
Auto . . . . . . . . . . . . . . . . . Auto Ranging
AC . . . . . . . . . . . . . . . . . . Alternating Current
DC . . . . . . . . . . . . . . . . . . Direct Current or Voltage
1.1. PERSONAL PRECAUTIONS
 When using this meter, please observe all normal safety rules concerning:
Protection against the dangers of electric current .
Protection of the meter against misuse .

Full compliance with safety standards can only be guaranteed if used with the test leads supplied . If necessary, they must be replaced with genuine Sealey
leads with the same electronic ratings . Failure to do so will invalidate the warranty .

DO NOT use leads if damaged or if the wire is bared in any way .
1.2. GENERAL SAFETY INSTRUCTIONS
 Familiarise yourself with the applications, limitations and hazards of the meter . IF IN ANY DOUBT CONSULT A QUALIFIED ELECTRICIAN.
 When the meter is linked to a measurement circuit, do not touch unused meter terminals .
 When the scale of the value to be measured is unknown set the selector to the highest range available .
 Before rotating the rotary switch to change functions, disconnect test leads from the circuit under test .
 WARNING! Never perform resistance measurements on live circuits.
 Always be careful when working with voltages above 60Vdc or 30Vac rms . Keep your fingers behind the probe guards while measuring .
 When not in use, store the meter carefully in a safe, dry, childproof location . Storage temperature range -10°C to 50°C .
 Never apply voltage or current to the meter that exceeds the specified maximum .
 The user shall ensure that test probes are correctly selected in order to prevent danger . Probes shall be selected to ensure that adequate barriers guard against
inadvertent hand contact with live conductors under test and that probes have minimal exposed probe tips . Where there is a risk of the probe tip short circuiting
with other live conductors under test, it is recommended that the exposed tip length shall not exceed 4mm .
Layout: (Refer to fig . 1 .)
1 . Large LCD display with symbolic signs .
2 . Rotary switch .
3 . Positive (+) input jack for AC/DC Voltage, AC/DC µ A/mA current, Hz/%Duty Cycle .
Ohms, Diode, Continuity, Capacitance, Temperature, (°C or °F) measurements,
RPM and Dwell .
4 . COM, negative input jack .
5 . 10A (positive) input jack for 10A AC or DC measurements .
6 . Frequency/Duty Cycle button .
7 . Range push button .
8 . Relative push button .
9 . Data hold .
10 . Backlight button .
11 . Mode push button .
INSTRUCTIONS FOR:
DIGITAL AUTOMOTIVE ANALYSER 13 FUNCTION
WITH IC
MODEL No:
TA201
Input Limits
Function Maximum Input
V AC or V DC 600V AC, 600V DC
mA AC/DC 400mA AC/DC
A AC/DC 10A AC/DC (30 secs
max every 15 minutes)
Frequency
Resistance
Capacitance
Duty Cycle
Diode Test
Continuity
Temperature
RPM
DWELL
Pulse Width
250V AC/DC
Compact size meter with four-digit 22mm, high contrast LCD display and backlight . Features auto-ranging, data hold and auto-power-off functions . Includes
inductive coupler for fast reading of engine RPM . Supplied with probe, crocodile clips and thermocouple leads for easy hook up .
Symbols & Description
Fig.1 Inductive Pickup Test Probes
Test Clips
TA201 Issue No: 3(L) - 17/06/14 Original Language Version
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
2. FEATURES
© Jack Sealey Limited