Sealey TA200 - Manual

INSTRUCTIONS FOR:
DIGITAL AUTOMOTIVE ANALYSER 8 FUNCTION
MODEL No: TA200
 WARNING! It is the user’s responsibility to read, understand and abide by the following safety instructions.
1.1. PERSONAL PRECAUTIONS
 When using this meter, please observe all normal safety rules concerning:
Protection against the dangers of electric current.
Protection of the meter against misuse.

Full compliance with safety standards can only be guaranteed if used with the test leads supplied. If necessary, they must be replaced with
genuine Sealey leads with the same electronic ratings. Failure to do so will invalidate the warranty.

DO NOT use leads if damaged or if the wire is bared in any way.
1.2. GENERAL SAFETY INSTRUCTIONS
 Familiarise yourself with the applications, limitations and hazards of the meter. IF IN ANY DOUBT CONSULT A QUALIFIED ELECTRICIAN.
 Before using the meter inspect the case. If you suspect any part of the case to be damaged or missing DO NOT USE THE METER.
Remove it from service immediately and contact your local Sealey dealer for advice/repairs.

When the meter is linked to a measurement circuit, do not touch unused meter terminals.
 When the scale of the value to be measured is unknown set the selector to the highest range available.
 Before rotating the rotary switch to change functions, disconnect test leads from the circuit under test.
 WARNING! Never perform resistance measurements on live circuits.
 Always be careful when working with voltages above 60Vdc or 30Vac rms. Keep your fingers behind the probe guards while measuring.
 When not in use, store the meter carefully in a safe, dry, childproof location. Storage temperature range -10 ºC to 50ºC.
 Never apply voltage or current to the meter that exceeds the specified maximum.
 Should the low battery indicator appear on the LCD display, replace the battery immediately (PP3). A low battery level could cause
the meter to produce inaccurate readings.

When not in use, store the meter in a safe, dry, cool and childproof location. DO NOT place in the proximity of a powerful source of
electromagnetic radiation.

The user shall ensure that test probes are correctly selected in order to prevent danger. Probes shall be selected to ensure that adequate
barriers guard against inadvertent hand contact with live conductors under test and that probes have minimal exposed probe tips. Where there
is a risk of the probe tip short circuiting with other live conductors under test, it is recommended that the exposed tip length shall not exceed
4mm.
1. LCD display
2. Data hold button
3. Rotary switch
4. Input terminals
5. Power ON/OFF
6. Crocodile clips
7. Probes
3.1. Rotary Switch (fig.1(3))
The rotary switch allows
selection of the various
functions available and of the
settings for each individual
function.
DC voltage measurement
AC voltage measurement
DC Current measurement
Diode test
Continuity test
Resistance measurement
Automotive ignition dwell testing (degrees)
Automotive engine tach (rotation speed)
testing (x10 rpm)
Rotary
Switch
Position
Function
Fig.1
Durable bi-composite case and integral stand suitable for the toughest workshop conditions. Large,
hi-contrast LCD display with 21mm high digital read-out. Unique Test Lead Connection feature
indicates correct hook-up. Includes data hold feature and low battery display. Supplied with test
probes, crocodile clips and comprehensive manual.
6
7
TA200 Issue No: 4(L) - 16/06/14 Original Language Version
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
2. INTRODUCTION
3. FEATURES
© Jack Sealey Limited