Yaskawa E7B Drive Bypass - Manual (Page 16)

Physical Installation 1 - 4
Enclosure Data
Table 1.2 208V Enclosure Data
Input
Volts
HP 1
Drive
Model
CIMR-
Bypass 2
Model
Number
NEC
FLA
OL
110%
1 min
Heat 3
Loss
Watts
Enclosure Dimensions 4
NEMA 1 & NEMA 12 -FVFF
H W D
inches
Weight 5
of
Assembly
Enclosure Dimensions w/Add-on 4
NEMA 1 & NEMA 12-FVFF
H W D
inches
Weight 5 of
Assembly
+Add-on
Box
Electrical
Schematic
208
0.5 E7U22P21 E7B_D002 2.4 2.6 68
29.48 19.06 13.66
Dimension Drawing 6
S-5512
115 lbs
43.35 19.06 13.66
Dimension Drawing
S-5513
156 lbs
E7B-00
0.75 E7U22P21 E7B_D003 3.5 3.8 68
1 E7U22P21 E7B_D004 4.6 5.1 78
2 E7U22P21 E7B_D007 7.5 8.2 110
3 E7U22P21 E7B_D010 10.6 11.7 141
5 E7U23P71 E7B_D016 16.7 18.4 202
7.5 E7U27P51 E7B_D024 24.2 26.6 273
10 E7U27P51 E7B_D030 30.8 33.9 365
127 lbs 164 lbs
15 E7U20111 E7B_D046 46.2 50.8 578
20 E7U20151 E7B_D059 59.4 65.3 653
40.48 25.63 14.66
Dimension Drawing 7
S-5514
208 lbs
55.35 25.63 14.66
Dimension Drawing
S-5515
291 lbs
25 E7U20181 E7B_D074 74.8 82.3 746
30 E7U20221 E7B_D088 88.0 96.8 939
221 lbs 307 lbs
40 E7U20301 E7B_D114 114.0 125.4 1340
50 E7U20370 E7B_D143 143.0 157.3 1523
84.00 25.63 26.25 8
Dimension Drawing 9
S-5525
847 lbs
NOT REQUIRED
60 E7U20450 E7B_D169 169.0 185.9 1762
943 lbs
75 E7U20550 E7B_D211 211.0 232.1 2244
100 E7U20750 E7B_D273 273.0 300.3 3003 1214 lbs
125 E7U20900 E7B_D343 343.0 377.3 3296 1330 lbs
150 E7U21100 E7B_D396 396.0 435.6 4029 1423 lbs
Note 1: Horsepower rating is based on a standard NEMA B 4-pole motor.
Note 2: The underscore position in these model numbers codes for the enclosure type: V = NEMA1, B = NEMA12 FVFF.
Note 3: Heat loss is the amount of heat dissipated by the drive at full load with all standard options available inside the enclosure. Drive heat sink losses are
included in the heat loss data. Heat loss data is for the enclosure without the add-on enclosure.
Note 4: Height dimension (H) excludes the mounting screw tabs. Depth dimension (D) excludes MCP disconnect handle.
Note 5: This data represents the total weight with all possible standard options. Weight could be less depending on the options specified.
Note 6: All standard options are available in this size enclosure except options E (RFI Filter) and K (5% Output Reactor). Options E and K require the add-on
enclosure.
Note 7: All options are available in this size enclosure except E (RFI Filter), R (3% Line Reactor), and K (5% Output Reactor). Only option E combined with
either option R or option K can be installed in the add-on enclosure. Options R and K together require an increase in the size of the E7 Bypass Enclosure.
Contact the factory if all three options are required. Options D (2 Motor “OR”) or A (2 Motor “AND”) for 30 Hp and 40 Hp, or for 75 Hp and 100 Hp, require
the next size enclosure.
Note 8: Heat sink mounted externally varies the depth dimension depending on the drive size. Depth will not exceed dimension shown.
Note 9: All options are available in this size enclosure except options D (2 Motor “OR”) or A (2 Motor “AND”) for 75 Hp and 100 Hp require the next
size enclosure.