Yaskawa V7 Drives - Manual (Page 130)

A2-2
SECTION B. All Drives (Continued)
Motor overload protection Electronic thermal overload relay
Motor coasts to stop at approx. 250%
Instantaneous overcurrent
of drive current
Motor coasts to stop after 1 min. at 150% of
Overload
drive rated current (7)
Motor coasts to stop if DC bus voltage exceeds
Overvoltage
410VDC (230V), 820VDC (460V)
Motor coasts to stop when DC bus voltage is
Undervoltage
210VDC or less (230V), 400VDC or less (460V)
The following operations are selectable:
Momentary Power Loss
• Not provided (stops if power loss is 15 ms or longer)
• Automatic restart at recovery from 0.5 sec. power loss
• Automatic restart
Heatsink overheat Protected by electronic circuit
Independently programmable during accel and
Stall prevention level
constant-speed running. Selectable during decel.
Ground fault Protected by electronic circuit (overcurrent level)
ON until the DC bus voltage becomes 50V or less.
Power charge indication RUN lamp says ON or digital operator LED stays ON.
(Charge LED is Provided for 400V)
Cooling Fan Fault Protected by electronic circuit
Run/stop input 2-Wire or 3-Wire
Seven of the following input signals are selectable:
Forward/reverse run (3-Wire sequence), fault reset,
external fault (NO/NC contact input), multi-step speed operation,
Multi-function input
Jog command, accel/decel time select,
external baseblock (NO/NC contact input, speed search command,
accel/decel hold command, LOCAL/REMOTE selection,
communication/control circuit terminal selection,
emergency stop fault emergency stop alarm
Following output signals are selectable
(1 NO/NC contact output, 2 photo-coupler outputs):
Fault, running, zero speed, at frequency, frequency detection
Multi-function output (output frequency ≤ or ≥ set value), during overtorque detection,
during undervoltage detection, minor error, during baseblock, operation mode,
inverter run ready, during fault retry, during UV, during speed search,
data output through communication
Analog monitor 0 to +10VDC output, programmable for output frequency or output current
Open Loop Vector Control, full-range automatic torque boost, auto restart,
Standard functions
upper/lower frequency limit, DC injection braking current/time at start/stop,
frequency reference gain/bias, prohibited frequencies,
analog meter calibrating gain, S-curve accel/decel, slip compensation,
MODBUS communications (RS485/422, Max. 19.2K bps),
frequency reference from digital operator pot
Status indicator LEDs RUN and ALARM LEDs provided as standard
Digital Operator
Monitors frequency reference, output frequency,
output current, FWD/REF selection
Terminals Screw terminals for both main circuit and control circuit
Wiring distance between
drive and motor
328 ft (100 m) or less (3)
Enclosure Open Type/NEMA type 1/NEMA type 4X/12
Cooling method Self-cooling/cooling fan
Ambient temperature 14 to 104°F (-10 to 40°C)
Humidity 95% RH or less (non-condensing)
Storage temperature (4) -4 to 140°F (-20 to 60°C)
Location Indoor (free from corrosive gases or dust)
Elevation 3,280 feet (1,000 m) or less
Vibration
Up to 1G, at less than 20 Hz;
up to 0.2G, at 20 to 50 Hz
Table A2-1. Standard Specifications (Continued)
Protectiv
e Functions
En
vironmental conditions
Other Functions
Input signals
Output signals
Displa
y
NOTES:
(1) Based on an N.E.C. standard 4-pole motor for max. applicable motor output.
(2) Shows deceleration torque for an uncoupled motor decelerating from 60 Hz in 0.1 seconds.
(3) Contact Yaskawa for wiring distances greater than 328 ft. (100 m).
(4) Temperature during shipping (for short periods of time).
(5) On NEMA type 4X/12 model only, maximum continuous rating of 30.8 A is 40 degrees C maximum ambient. For 33.0 A maximum
continuous rating, maximum ambient is 32 degrees C.
(6) Applies to NEMA type 4X/12 model only.
(7) On Model 47P5 NEMA type 4X/12 (21A), overload is 120% for 1 minute.