HEIDENHAIN ND 231 B v.2 - Manual (Page 46)

46
Output
Format
of
the
Parameter
List
Parameter list for ND 231 B: (factory default setting)
Parameter list Description
*
Start character (*);
ND-231 B MM Model of display unit; MM or IN;
P01 MM = MM = 0 Unit of measure: MM = 0; INCH = 1;
P06 DISPL. = X1 ADD. X2 = 2
X1 = 0; X2 = 1; X1 ADD. X2 = 2; X1 SUB. X2 = 3;
P11 SCL = SCALING OFF = 0
SCALING FACTOR OFF = 0; ON = 1;
P12.1 SCL = 1.000000 X1: SCALING FACTOR = 1.000000; (value input without sign)
P12.2 SCL = 1.000000 X2: SCALING FACTOR = 1.000000; (value input without sign)
P17 CLASS. = CLASS. OFF = 0
Sorting : CLASS. OFF = 0; CLASS. ON = 1;
P18 L.CLASS. = + 0.0000 Lower limit: L.CLASS = 0; (value input)
P19 U.CLASS. = + 0.0000 Upper limit: U.CLASS = 0; (value input)
P23 DISPL. = DISPL. ACTL. = 0
DISPLAY: ACTUAL = 0; FREEZE = 1; STOP = 2;
P30.1 DIR = DIRECT. POS = 0
X1: COUNTING DIRECTION POS = 0; NEG = 1;
P30.2 DIR = DIRECT. POS = 0 X2: COUNTING DIRECTION POS = 0; NEG = 1;
P31.1 S. PER. = 10
X1: SIGNAL PERIOD = 10 µm; (value input without sign)
P31.2 S. PER. = 10
X2: SIGNAL PERIOD = 10 µm; (value input without sign)
P33.1 STEP = COUNT 0-5 = 5 X1: COUNTING MODE 0-5 = 5; 0-2 = 2; 0-1 = 1;
P33.2 STEP = COUNT 0-5 = 5 X2: COUNTING MODE 0-5 = 5; 0-2 = 2; 0-1 = 1;
P38.1 DEC. = DP POS. 4 = 4
X1: DECIMAL PLACES 4 (range: 1-8)
P38.2 DEC. = DP POS. 4 = 4 X2: DECIMAL PLACES 4 (range: 1-8)
P40.1 COMP. = COMP. OFF = 0 X1: COMPENSATION OFF = 0; LIN = 1; MULTI = 2;
P40.2 COMP. = COMP. OFF = 0
X2: COMPENSATION OFF = 0; LIN = 1; MULTI = 2;
P41.1 L.COMP. = + 0.0
X1: LINEAR COMPENSATION = 0 µm/m (value input)
P41.2 L.COMP. = + 0.0 X2: LINEAR COMPENSATION = 0 µm/m (value input)
P42.1 BKLASH = + 0.0000
BACKLASH compensation = 0.0000 mm (value input)
P42.2 BKLASH = + 0.0000
BACKLASH compensation = 0.0000 mm (value input)
P43.1 REF = SINGLE REF. = 0 X1: SINGLE REF. = 0; 500; 1000; 2000; 5000 SP;
P43.2 REF = SINGLE REF. = 0 X2: SINGLE REF. = 0; 500; 1000; 2000; 5000 SP;
P44.1 REF = REF. ON = 1
X1: REF.ON = 1; REF. OFF = 0;
P44.2 REF = REF. ON = 1 X2: REF.ON = 1; REF. OFF = 0;