Airaid 350-210 - Manual (Page 2)

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected] www.airaid.com
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951
8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions that are not clear to
you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter
element is protected from direct exposure to water and debris; care should be taken not to drive
through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.
12. For 5.7L V8 HEMI equipped vehicles:
Locate the V8 Airaid Intake Tube marked KIT-210-8T
and insert the larger, 3/4” Grommet (#23) and one of
the larger, 3/4” Barbed fittings (#25) into the side. Com-
plete the V8 Tube assembly by installing the 2 1/2’’ ,
3/4” Hose (#10) onto the Tube Fitting, and inserting the
second 3/4” Barbed Fitting into it as shown.
9. Lower the Panel Assembly into the inner fender area
and align the mounting holes. Be sure to insert the bot-
tom of Front Panel between the ABS line and the sheet
metal. Secure the assembly using:
One, 1/4-20 Button Head bolt (#12) and 1/4” Flat Wash-
er (#13), Underneath the factory core support tab (A),
The 3/8 Button Head Bolt (#14) and Flat Washer (#15)
in the Well Nut (B) , and the factory fender bolt from
step 8 (C). 10. Snap the Line Holder (#22) onto the ABS line closest
to the panel assembly and remove the adhesive backing.
Gently push the Panel away from the line and slide the
Line Holder behind the Panel. Relax the Panel, and allow
the Adhesive pad to bond the Panel. This will isolate the
Panel and prevent contact with the ABS line. 11. For 3.6L V6 Pentastar equipped vehicles:
Locate the V6 Airaid Intake Tube marked KIT-210-6T
and insert the smaller, 5/8” Grommet (#24) into the
side. Complete the V6 Tube assembly by inserting the
smaller, 5/8” Barbed fitting (#27) into the Grommet.
REV01.13.15
13. For 6.4L V8 SRT-8 equipped vehicles:
Locate the V8 Airaid Intake Tube marked KIT-210-8T
and insert the larger, 3/4” Grommet (#24) into the side.
Complete the SRT-8 Tube assembly by inserting the 5/8”
90 Degree, Barbed Fitting (#26) into the Grommet as
shown. 14. Install the Hump Hose (#7) and Clamps (#20) onto
the Filter Adapter. Leave the Clamps loose for now.
15. Install the Intake Tube into the Hump Hose and fac-
tory intake tube. When properly installed the location
lug in the factory tube will mate with the notch in the
Airaid Intake Tube. Tighten the clamps and connect the
crank case breather to the Intake Tube. 16. For 3.6L V6 Pentastar equipped vehicles:
Install the Smaller, 5/8” hose (#11) onto the Barbed Fit-
ting and factory hard line. Snap a Speed Clamp (21) on
each end of the hose to secure it in place.
17. Install the Weatherstrip (#8) onto the top edge of
the Panels with the contour rolling away from the Filter
area. Complete the installation by attaching the Airaid
Premium Filter (#1) to the Filter Adapter.
Double check your work!
Make sure there is no foreign material in the
intake path. Make sure all clamps, hoses,
bolts, and screws are tight. Double check the
hood clearance!
Reconnect the negative battery cable!
A
C
B
UNDERSIDE
For your Oiled media filter we suggest
using the AIRAID Filter Tune-Up Kit!
Synthamax Air Filters do not require oil. Ser-
vice air filter as needed by cleaning with com-
mon non-petroleum all-purpose household
cleaner and water. Simple Green®, Formula
409® or equivalent works great. Apply cleaner
to outside of air filter and allow to soak. Then
flush filter clean from the inside out with a gar-
den hose and repeat steps if necessary. Do not
apply high pressure water or air to clean filter.
Allow filter to air dry and reinstall
.
FILTER IDENTIFICATION
720-243 Airaid Oiled Media 721-243 Airaid SynthaMax Dry Media - Red
722-243 Airaid SynthaMax Dry Media - Black 723-243 Airaid SynthaMax Dry Media - Blue