Sloan 601 Prison Flushometer - Manual

Code No. 0816331
Rev. 4 (05/13)
INSTALLATION INSTRUCTIONS FOR STAINLESS STEEL
WATER CLOSETS, URINALS AND COMBINATION FIXTURES
Check that the “L” dimension shown on the flushometer package is correct for your
application. Determine the “L” dimension for your application by using the following
formula:
“L” dimension = Wall Thickness (to the nearest whole inch) + 2-3/4” (Models
609, 611 and 613), 4-3/4” (Models 601 and 603) OR 6-3/4” (Model 681).
Prior to installing the Sloan Prison Flushometer, perform the following functions using
the rough-in diagrams on Pages 2 and 3.
• Bore a 1-1/2” (38 mm) opening in wall for standard or hydraulic push button
actuator
• Bore a 1-2” (25-51 mm) opening in wall for piping. Refer to the Rough-in
drawings on Pages 2 and 3. (This is NOT required if wall sleeve is used in
conjunction with fixture.)
• Install stainless steel prison fixture
• Install drain line
• Install water supply line
IMPORTANT:
• INSTALL ALL PLUMBING IN ACCORDANCE WITH APPLICABLE CODES AND
REGULATIONS.
• WATER SUPPLY LINES MUST BE SIZED TO PROVIDE AN ADEQUATE
VOLUME OF WATER FOR EACH FIXTURE.
• FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.
Sloan’s flushometers are designed to operate with 10 to 100 psi (69 to 689 kPa)
of water pressure.
THE MINIMUM PRESSURE REQUIRED BY THE VALVE IS
DETERMINED BY THE TYPE OF FIXTURE SELECTED.
Consult fixture manufacturer for minimum pressure requirements. Most Low
Consumption water closets (1.6 gpf/6.0 Lpf) require a minimum flowing pressure of
25 psi (172 kPa).
LIMITED WARRANTY
Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold for commercial or industrial uses, to be free from defects in material and
workmanship for a period of three (3) years (one (1) year for special finishes, SF faucets, PWT electronics and 30 days for PWT software) from date of first purchase. During
this period, Sloan Valve Company will, at its option, repair, replace, or refund the purchase price of any product which fails to conform with this warranty under normal use
and service. This shall be the sole and exclusive remedy under this warranty. Products must be returned to Sloan Valve Company, at customer’s cost. No claims will be
allowed for labor, transportation or other costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan
Valve Company for purpose of resale. This warranty does not cover the life of the batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY
CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
Concealed Flushometer
with Standard
Push Button Actuator
Closet Flushometer
1½” (38 mm) Back Inlet
MODELS 601, 603, 611 & 681
Urinal Flushometer
1½” (38 mm) & 3/4” (19 mm)
Back Inlet
MODELS 609 & 613
Concealed Flushometer
with Hydraulic
Push Button Actuator
Closet Flushometer
1½” (38 mm) Back Inlet
MODEL 9603
Urinal Flushometer
1½” (38 mm) & 3/4” (19 mm)
Back Inlet
MODELS 9609 & 9613
Made in the U.S.A.
PRIOR TO INSTALLATION
TOOLS REQUIRED FOR INSTALLATION
• Standard set of hex wrenches
• Parker Tube Cutter (PTC) • Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth jawed spud
wrench