Sloan 110 Dolphin Flushometer - Manual

Code No. 0816335
Rev. 1 (06/12)
LIMITED WARRANTY
Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold for commercial or industrial uses, to
be free from defects in material and workmanship for a period of three (3) years (one (1) year for special finishes, SF faucets, PWT
electronics and 30 days for PWT software) from date of first purchase. During this period, Sloan Valve Company will, at its option,
repair, replace, or refund the purchase price of any product which fails to conform with this warranty under normal use and service.
This shall be the sole and exclusive remedy under this warranty. Products must be returned to Sloan Valve Company, at customer’s
cost. No claims will be allowed for labor, transportation or other costs. This warranty extends only to persons or organizations who
purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the
life of the batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN
VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
INSTALLATION INSTRUCTIONS FOR STANDARD EXPOSED DOLPHIN ®
WATER CLOSET AND URINAL FLUSHOMETERS
Before you install the Sloan Dolphin Flushometer, install the items listed
below. Also, refer to the rough-in diagrams on Page 2.
• Closet or urinal fixture
• Drain line
• Water supply line
IMPORTANT:
• INSTALL ALL PLUMBING IN ACCORDANCE WITH
APPLICABLE CODES AND REGULATIONS.
• WATER SUPPLY LINES MUST BE SIZED TO PROVIDE AN
ADEQUATE VOLUME OF WATER FOR EACH FIXTURE.
• FLUSH ALL WATER LINES PRIOR TO MAKING
CONNECTIONS.
• A GROUND JOINT STOP IS RECOMMENDED FOR ALL
SALTWATER AND SEAWATER APPLICATIONS. SPECIFY
“-GJ” VARIATION WHEN ORDERING.
• A VACUUM BREAKER IS USUALLY NOT REQUIRED
WHEN WATER SUPPLY IS NON-POTABLE. SPECIFY
“-XYV” VARIATION WHEN ORDERING.
• A VACUUM BREAKER IS NOT SUPPLIED WITH
SHIPBOARD MODELS.
The Sloan Dolphin Flushometer is an adjustable valve designed to operate
with 10 to 100 psi (69 to 689 kPa) of water pressure. THE MINIMUM
PRESSURE REQUIRED TO THE VALVE IS DETERMINED BY
THE TYPE OF FIXTURE SELECTED. Consult fixture manufacturer for
minimum pressure requirements. Most Low Consumption water closets (1.6
gpf/6.0 Lpf) require a minimum flowing pressure of 25 psi (172 kPa).
For Saltwater, Seawater and all Shipboard Flushometers, Sloan Valve Company recommends furnishing Dolphin Valves with a Ground Joint Supply Stop. Specify
“-GJ” (Ground Joint) variation. Standard Shipboard Flushometers use Ground Joint Supply Stops.
Saltwater and other non-potable water supplies do not typically require the use of Vacuum Breakers.
To order a Flushometer without a Vacuum Breaker, specify “-XYV” variation.
Shipboard Flushometer Valves can be supplied with a Sil-Braze Inlet Adapter. Please specify when ordering. For Type I Water Closet applications, use a 1” (25 mm)
adapter. For Type II Urinal applications, use a 1/2” (13 mm) adapter.
Type I and Type II Shipboard Models: For U.S. Navy per Military Specification MIL-V-0015010F (Ships)
STANDARD MODELS
Exposed Closet Flushometer
1½” (38 mm) Top Spud
MODELS 110/111 & 115
Exposed Closet Flushometer
1½” (38 mm) Back Spud
MODEL 120
Exposed Urinal Flushometer
¾” (19 mm) Top Spud
MODEL 186
SHIPBOARD MODELS
Model Type I Class A
Exposed Shock Proof
Closet Flushometer
1½” (38 mm) Shock Proof Scored Outlet
Model Type I Class B
Exposed Rigid Installation
Closet Flushometer
1½” (38 mm) Rigid Installation
Model Type II Class A
Exposed Shock Proof
Urinal Flushometer
¾” (19 mm) Shock Proof Scored Outlet
Model Type II Class B
Exposed Rigid Installation
Urinal Flushometer
¾” (19 mm) Rigid Installation
Models 110/111 Model 186 Model 120
SHIPBOARD MODELS
PRIOR TO INSTALLATION
TOOLS REQUIRED FOR INSTALLATION
• Straight blade screwdriver
• 1/16” hex wrench for wall flange
• Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth jawed spud wrench