Orion System SA E-BUS Controller - Manual (Page 31)

SA E-BUS Controller Technical Guide
Installation & Wiring
31
12-Relay Expansion Module Overview and Wiring
EXP1
EXP1
EXP2
EXP2
Set Jumper As Shown
Above When Both The 12
Relay & SA Expansion
Module Are Used
12-Relay
Expansion Module
Set Jumper As Shown
Below When Only The
12 Relay Expansion
Module Is Used
POWER
RLY1
RLY2
RLY3
RLY4
RLY COM
EXP1
EXP2
24VAC
GND EXPANSION BOARD
YS102228 REV 1
RELAY
RLY5
RLY6
RLY7
RLY8
RLY COM
RLY9
RLY10
RLY11
RLY12
RLY COM
MADE IN USA
SET JUMPER AS
SHOWN WHEN
THE 12 RELAY
EXPANSION MODULE
IS USED
ONLY
SET JUMPER AS
SHOWN WHEN BOTH
THE SA EXPANSION
MODULE AND THE
RELAY EXPANSION
MODULE ARE USED
J1 J1
EXP1 EXP1
EXP2 EXP2
NOTE:
IT IS RECOMMENDED THAT YOU WRITE THE
DESCRIPTION OF THE RELAY OUTPUTS YOU
ARE CONNECTING TO THE RELAY EXPANSION
MODULE IN THE BOXES PROVIDED ABOVE
USING A PERMANENT MARKER (SHARPIE)
FOR FUTURE REFERENCE.
®
WattMaster Label
#LB102043
I2C
EXPANSION
I2C
EXPANSION
24 VAC POWER ONLY WARNING! POLARITY MUST BE
OBSERVED OR THE BOARD
WILL BE DAMAGED
www.orioncontrols.com
RLY 1 = RLY 7 =
RLY 2 = RLY 8 =
RLY 3 = RLY 9 =
RLY 4 = RLY 10 =
RLY 5 = RLY 11 =
RLY 6 = RLY 12 =
OE358-23-12R-A 12 RELAY EXPANSION MODULE
Configurable Relay Output #9 Configurable Relay Output #1
Configurable Relay Output #5
R9 R1
R5
R10 R2
R6
R11 R3
R7
R12 R4
R8
Configurable Relay Output #10 Configurable Relay Output #2
Configurable Relay Output #6
Configurable Relay Output #11 Configurable Relay Output #3
Configurable Relay Output #7
Configurable Relay Output #12 Configurable Relay Output #4
Configurable Relay Output #8
Relay Output Contacts
R1 Through R12 May Be User-Configured
For The Following:
Note:
-
1 - Heating Stages
2 - Cooling Stages
3 - Warm-up Mode Command (VAV Boxes)
4 - Reversing Valve (Heat Pumps)
5 - Reheat Control (Dehumidification)
6 - Preheater For Low Ambient Protection
7 - Alarm
8 - Override
9 - Occupied
10 - Water Side Economizer
A Total Of 20 Relays Are Available By
Adding Relay Expansion Modules. All
Expansion Module Relay Outputs Are User
Configurable As Listed Above.
Modular Cable
Connect To SA E-BUS Controller
Modular Cable
Connect To Next Expansion Board
(When Used)
24 VAC
GND
15 VA Minimum Power
Required For
OE358-23-12R
12 Relay Expansion Module
WARNING!!
Observe Polarity! All boards must be wired with GND-to-GND and 24VAC-to-24VAC. Failure to observe polarity will result in damage to one or
more of the boards. Expansion Modules must be wired in such a way that the expansion modules and the controller are always powered
together. Loss of power to the expansion module will cause the controller to become inoperative until power is restored to the expansion module.
Note:
All Relay Outputs Are Normally Open
And Rated For 24 VAC Power Only.
1 Amp Maximum Load.
The expansion modules can be used individually or together to provide
the required inputs and outputs for your specifi c applications.
When using the 12-Relay Expansion Module, you must correctly confi g-
ure a set of jumpers on the board depending on whether it will be used
by itself or in addition to the SA Expansion Module.
The jumpers are located on the edge of the 12-Relay Expansion Module
on the same side of the module as the power connection. See Figure
25 below for details regarding setting the switch correctly for your
application.
Figure 25, cont.: OE358-23-12R – 12-Relay Expansion Module Wiring and Jumper Settings