Hypath i/o connectors, Hypath i/o connectors -23 – Hypertherm MicroEDGE Pro Shape Cutting Control Rev.2 User Manual
Page 71
InstallatIon
MicroEDGE Pro
Instruction Manual 807290
2-23
HyPath I/o connectors
HyPath I/o connectors
Notes:
• Isolate all external commons from the chassis ground.
• If external voltage is used to activate I/O, connect the external source’s common to the internal +24 V common.
• HyPath systems have the I/O for each connector printed above the connectors.
Use the following information to create HyPath I/O cables.
The HyPath I/O mating connector is a 37-pin, circular connector:
• Cable connector: AMP 206305-1
• Pin contacts: AMP 66098 (16–18 AWG), AMP 66331 (20–24 AWG)
• Hypertherm kit: 228492
The following pages provide additional specifications and pinout information for the HyPath interface boards.
1
5
10
16
23
29
34
4
9
15
22
28
33
37
HyPath I/o connector
Location of the I/o connectors
J6 I/O 7-12
J7 I/O 1-6
J5 I/O 13-18
J4 I/O 19-24
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- Powermax1650 (317 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)