Hypertherm MicroEDGE Pro Shape Cutting Control Rev.2 User Manual
Page 148
Maintenance and diagnostics
4-52
MicroEDGE Pro
Instruction Manual 807290
Connector j7 (
to front panel on/off switch
)
Pin no. Signal
1
Ground
2
12 V
3
Motherboard on/off 2
4
Motherboard on/off 1
Connector j9 (
to and from Motherboard and
power distribution
)
Pin no. Signal
1
Field power
2
Not connected
3
Ground
4
Motherboard on/off 2
5
Motherboard on/off 1
Connector j8 (Serial port A, CoM3)
Pin no. Signal
1
Not connected
2
Transmit A-
3
Receive A-
4
Transmit A+
5
Signal ground 1
6
Not connected
7
Receive A+
8
Not connected
9
Not connected
Connector j12 (Serial port B, CoM4)
Pin no. Signal
1
Not connected
2
Transmit B-
3
Receive B-
4
Transmit B+
5
Signal ground 2
6
Not connected
7
Receive B+
8
Not connected
9
Not connected
Connector j4 (
Remote on/off
)
Pin no. Signal
1
Remote on/off +
2
Remote on/off -
3
Common
4
12 V
5
Shield
Connector j3 (
To Serial COM3 and COM4
)
Pin no. Signal
1
Ground
2
DR_A
3
/RXD_INA
4
TS_A
5
TXD_OUTA
6
TS_A
7
DR_A
8
Ground
9
Ground
10
Not connected
11
Ground
12
DR_B
13
/RXD_INB
14
TS_B
15
TXD_OUTB
16
TS_B
17
DR_B
18
Ground
19
Ground
20
Not connected
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Powermax1650 (317 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)