Diagnostic tests, Diagnostic tests -4 – Hypertherm MicroEDGE Pro Shape Cutting Control Rev.2 User Manual
Page 100
Maintenance and diagnostics
4-4
MicroEDGE Pro
Instruction Manual 807290
Diagnostic tests
Note: Test kits are required to perform the following diagnostic tests.
Machine interface tests
If you are using a MicroEDGE Pro CNC, you can perform diagnostic tests with the following connectors and Phoenix
software to test the interface ports on the CNC (228831):
•
Serial interface RS-232 on the motherboard
•
Serial interface RS-422 on the serial isolation board
•
Ethernet and Hypernet
•
USB
Note: This is the only kit needed for SERCOS II and SERCOS III systems and it is included in the HyPath and
Picopath kits.
The HyPath version of the MicroEDGE Pro CNC offers the following, additional testers (228832):
•
I/O (2)
•
Axes
•
THC
•
Joystick and speedpot
The Picopath version of the MicroEDGE Pro CNC offers the following, additional testers (228833):
•
I/O (2)
•
Axes
•
THC
•
Joystick and speedpot
Machine interface test screen
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- Powermax1650 (317 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)