Rear panel, Rear panel -6 – Hypertherm MicroEDGE Pro Shape Cutting Control Rev.2 User Manual
Page 40
SpecificationS
1-6
MicroEDGE Pro
Instruction Manual 807290
Drive/encoder ports
Rear panel
The rear panel of the CNC has cable connectors for power, motion control feedback, I/O, and communication ports.
These connectors are clearly labeled with their function. There are four configurations available: HyPath, Picopath,
SERCOS II, and SERCOS III.
For more information about the electrical installation of the MicroEDGE Pro CNC, see Section 3, Installation.
Note: The rear panel shown below is for reference only. The rear panel on individual CNC units depends on which
configuration is ordered.
Rear panel of the Picopath MicroEDgE Pro CNC
Serial
ports on the
mother board
(RS-232)
USB
ports
Hypernet
port
AC
power
input
Optional
Sensor THC
ports (2)
I/O port
LAN
port
VGA
port
Optional joystick and
speedpot port
Serial
ports on the
serial isolation
board
(RS-422 or
RS-232)
Remote On/Off
Antenna ports
for optional
wireless I/O
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Powermax1650 (317 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)