Hypertherm MicroEDGE Pro Shape Cutting Control Rev.2 User Manual
Page 171
6-13
SHEET
1
2
3
4
4
3
2
1
A
B
C
D
D
C
B
A
J5
J1
J2
J3
J4
NOT USED
Ground 1
THC1_Nozzle_Contact_Sense+ 2
THC1_Nozzle_Contact_Sense- 3
THC1_Nozzle_Contact_Enable_A 4
THC1_Nozzle_Contact_Enable_B 5
THC1_Arc_Volts+ 6
THC1_Arc_Volts- 7
THC1_Hold_Ignition_A 8
THC1_Hold_Ignition_B 9
THC2_Nozzle_Contact_Sense+ 10
THC2_Nozzle_Contact_Sense- 11
THC2_Nozzle_Contact_Enable_A 12
THC2_Nozzle_Contact_Enable_B 13
THC2_Arc_Volts+ 14
THC2_Arc_Volts- 15
THC2_Hold_Ignition_A 16
THC2_Hold_Ignition_B 17
10V_Reference 18
Joystick_UP 19
Joystick_DOWN 20
Joystick_LEFT 21
Joystick_RIGHT 22
Speed_Pot1+ 23
Speed_Pot1- 24
Speed_Pot2+ 25
Speed_Pot2- 26
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
10-C3
223234
PCB4
ANALOG-THC PCB
141125
J
SHEET 9 OF 20
ANALOG THC PCB
See also other documents in the category Hypertherm Equipment:
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Powermax1650 (317 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)