Q-See QSC26408 User Manual

Commercial series net dvr user manual (v2.0)

Table of contents

Document Outline

Version Description
Chapter 1 Product Introduction
- 1.1 Summary
- 1.2 Features
Chapter 2 Installation
- 2.1 Checking the DVR and Its Accessories
- 2.2 HDD Installation
- 2.3 Rear Panel Description
  - 2.3.1 8-ch QSD42208 Rear Panel
  - 2.3.2 8-ch/16-ch QSC26408/16 Rear Panel
- 2.4 External Alarm In/Out Connection
Description
Physical Interface
Index
Description
Physical Interface
Index
Chapter 3 Operational Instructions
- 3.1.1 8-ch QSD42208 Front Panel
- 3.1.2 8-ch QSC26408 Front Panel
- 3.1.3 16-ch QSC26416 Front Panel
- 3.2 Remote Control
- 3.3 Menu Description
  - 3.3.1 Menu Items
  - 3.3.2 Menu Operation
- 3.4 Character Input
Display
Chapter 4 Basic Operation Guide
- 4.1 Power on
- 4.2 Preview
- 4.3 User name and password
- 4.4 PTZ Control
- 4.5 Manual Record
- 4.6 Playback
- 4.7 Backup Recorded Files
- 4.8 Shut Down DVR
Status Description
Icon Color
Chapter 5 Main and Aux Output Function
- 5.1 Main and aux output
- 5.2 Main and Aux output preview
- 5.3 Main and Aux output playback
- 5.4 Main or Aux output to control PTZ
Chapter 6 Parameters Setup Guide
- 6.1 Administrator and Password
- 6.2 Add and Delete User
- 6.3 Unit Name and Device ID
- 6.4 Video Output Standard and VGA Setup
- 6.5 OSD Setup
- 6.6 Video Parameters Setup
- 6.7 Mask Area Setup
- 6.8 View Tampering Alarm
- 6.9 Video Loss Alarm
- 6.10 Motion Detection Alarm
- 6.11 Preview Properties
- 6.12 Recording Setup
- 6.13 External Alarm Input and Relay Output
- 6.14 Network Parameters
- 6.141 Accessing the DVR over a network
- To access the DVR through a computer you need to make sure the default gateway on the DVR is the same IP address as your router, and the first three sets of numbers of the DVR IP address are the same as the first three sets of numbers of router’s addr...
- You can access the DVR through an Internet Explorer browser window, or through the included client software program.
- 6.142 Accessing the DVR from a remote computer
- To access the DVR from a remote computer, in addition to the above steps, you will also need to forward ports 80 and 8000 on the router the DVR is attached to, to the IP address of the DVR. How you would do this depends on the brand and model number o...
- You can access the DVR through an Internet Explorer browser window, or through the included client software program.
- To access the DVR through Internet Explorer: once you have setup the network settings on the DVR to match the settings of your router and forwarded the ports needed by the DVR, you need to modify your browser controls. You need to allow Pop-ups. To do...
- 6.15 PTZ
  - Preset setup
- 6.16 RS232 setup
  - RS232 menu description
  - Example: PPP (Modem) passive dialup through PSTN
- 6.17 Exceptions
- 6.18 Transaction Information
Chapter 7 Utilities
- 7.1 Save Parameters
- 7.2 Restore Parameters
- 7.3 Upgrade
- 7.4 Hard Disk Management
- 7.5 Clear Alarm Out
- 7.6 Reboot
- 7.7 Power Off
- 7.8 View Log
- 7.9 System Information
Chapter 8 Firmware Upgrade
- 8.1 FTP Server Setup
- 8.2 Upgrade Mode
Appendix A HDD Capacity Calculation
Appendix B DVR Connect Cable Definition
- 1 How to make a RS-485 connect cable
- 2 How to make a UTP network connect cable
- 3 How to make a RS-232 connect cable
Appendix C Specifications
Appendix D Quick Search Function Table
Appendix E Troubleshooting
Appendix F Product Service
Appendix G Customer Information Card