AMETEK SGI Series - Manual (Page 21)

Sorensen SGI Series Overview
M550221-01 Rev AA 1-7
1.2.3 SGI Series Voltage and Current Specifications
The following tables present the specifications for rated voltage and current, and ripple/noise for
the 10V-1000V models.
Rated
Voltage,
VDC
Rated Current, ADC
Ripple/
Noise**
RMS,
mV
Ripple/
Noise*
PK –PK,
mV
4 kW 5 kW 8 kW 10 kW 12 kW 15 kW
0-10
††
0-400 N/A 0-800 N/A 0-1200 N/A 20 50
0-15
††
0-267 N/A 0-534 N/A 0-801 N/A 20 50
0-20
††
N/A 0-250 N/A 0-500 N/A 0-750 20 60
0-30
††
N/A 0-167 N/A 0-334 N/A 0-501 20 60
Rated
Voltage,
VDC
Rated Current, ADC
Ripple/
Noise**
RMS,
mV
Ripple/
Noise*
PK –PK,
mV
5 kW 10 kW 15 kW 20 kW 25 kW 30 kW
0-40 0-125 0-250 0-375 0-500
†
0-625
†
0-750
†
20 75
0-50 0-100 0-200 0-300 0-400
†
0-500
†
0-600
†
20 75
0-60 0-83 0-167 0-250 0-333 0-417 0-500
20 75
0-80 0-63 0-125 0-188 0-250 0-313 0-375
20 100
0-100 0-50 0-100 0-150 0-200 0-250 0-300
20 100
0-160 0-31 0-63 0-94 0-125 0-156 0-188
25 150
0-200 0-25 0-50 0-75 0-100 0-125 0-150
25 175
0-250 0-20 0-40 0-60 0-80 0-100 0-120
30 200
0-300 0-17 0-33 0-50 0-67 0-83 0-100
30 200
0-330 0-15 0-30 0-45 0-61 0-76 0-91
30 200
0-400 0-12 0-25 0-38 0-50 0-63A 0-75
30 300
0-500 0-10 0-20 0-30 0-40 0-50 0-60
50 350
0-600 0-8 0-17 0-25 0-33 0-42 0-50
60 350
0-800 0-6.2 0-12.5 0-18.7 0-25
†
0-31.2
†
0-37.5
†
80 500
0-1000 0-5 0-10 0-15 0-20
†
0-25
†
0-30
†
100 650
* PK-PK ripple/noise, over 20 Hz to 20 MHz bandwidth, is measured across a 1 µF capacitor at
the end of a 6’ load cable with the supply operating at full load and nominal AC line voltage.
** RMS ripple/noise, over 20 Hz to 300 kHz bandwidth, is measured directly across the output
terminals with the supply operating at full load and nominal AC input line voltage.
†
Power level not available in 6U models, but could be produced with paralleled 3U units; up to
75 kW could be produced by paralleling up to five units. Paralleling will increase ripple/noise.
††
Models from 10V-30V are not available in 6U chassis.