Genie Pro max PMX-IC B Series - Manual (Page 23)

NEC
CLASS 2
1
2
3
4
5
6
MORE
FORCE
USH
UTT N
AFE Y
EAM
IMIT
ET
PEN
OR
LOS
ORCE
ADIO
IGN L
EARN
ODE
OM
O N T
P SH
L M T N E S
O R I
A T C E
NOTE
USE O LY W TH ER E CON RO S
CLOSE
MORE OPEN
MORE
CLOSE OPEN
LIMIT ADJUSTMENT
U S Pa ent No 5 243 7 4 5 221 869
WARNING
CONTACT REVERSE
Fine adjustments for limit switches (see Section 8)
MUST BE completed before starting CONTACT
REVERSE.
•
Open door, use wall control.
•
Place a 2 by 4 board laid flat in center of doorway.
•
Close door.
•
Door MUST stop and reverse to open position. If it
does not, repeat fine adjustments for down limit
switch and
“
CLOSE FORCE
”
adjustment until the
door will reverse to the open position.
NNOTTE:: Set miniimuum ffoorce rrequiired tto make ddooor cloose..
If door does not reverse, decrease
“
CLOSE FORCE
”
until door reverses.
During the following steps, the motor protector may
open.Wait about 20 minutes for protector to reset.
NNOOTE: Usse wall ccontroll to run ddoooor to the fuullyy
CCLLOOSEED posiitioonn beffoorree starttiing
“
OOPEEN FOORCE
”
aaaaddjjuuusstttmmmeenntttt...
1. Adjust the
“
OPEN
”
Force (Fig. 7-1).
•
Locate screw on back of power head marked
“
OPEN FORCE.
”
•
Gently turn screw counterclockwise until it stops.
NNOOTE:: LLiittlee effffoorttis rreequuiired too tturn aadjuusstinng sccreew.
•
Operate door using wall control.
•
If door does not completely open, turn
“
OPEN
FORCE
”
screw clockwise slightly.
•
Activate door using wall control.
•
Repeat force adjustment until door will
completely open.
NNOTTE:: Seett minimmumfoorce requiireed tto make dooor oopen.
•
Close door, use wall control.
2. Adjust the
“
CLOSE FORCE
”
(Fig. 7-1). Use wall
control to run door to the fully OPEN position
before starting
“
CLOSE FORCE
”
adjustment.
•
Locate screw on back of power head marked
“
CLOSE FORCE.
”
•
Gently turn screw counterclockwise until it stops.
NNOOTE:: LLiittlee effffoorttis rreequuiired too tturn aadjuusstinng sccreew.
•
Operate door using wall control.
•
If door does not completely close, turn
“
CLOSE
FORCE
”
screw clockwise slightly.
•
Operate door using wall control.
•
Repeat force adjustment until door will
completely close.
NNOTE: Sett the mminimmuumm foorrcce rreequirreed to makke the
ddoooorr cloosse.. Smalllerr tthhee numberr thhee smmaalller the
ffffoooorrrccee..
3. (Fig. 7-2)
Adjust your door operator so that minimum force
is needed to operate door.
Position ladder to the side of the power head so
that it is clear of all moving parts of the power
head, rail assembly and door.
Fig. 7-2
1 1/2
”
Object
(or a 2 x 4
laid flat)
CONTACT REVERSE
Fig. 7-1
MO E MORE
L MIT ADJUSTMENT
C OSE OPEN
PUSH
LIM TS
TO SET
4
3
2
1
CLASS 2
NEC
OP N
CL SE
OR
MORE
FORCE
LIMIT
SET
OPEN
FORCE
CLOSE
FORCE
RADIO
SIGNAL
LEARN
CODE
MOR MOR
OSE
LI
PRO MAX
STEALTH
7777
......
FOORCEE AADDJJUSTTMEENT
FFOR HELP-1.800..3554.36433 OR GENIEECCOOMPANY.CCOOM
23