beautypg.com

Maintenance and lubrication, Maintenance, Lubrication – Sears 113.19771 User Manual

Page 34: Recommended accessories

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

background image

maintenance and lubrication

MAINTENANCE

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH

"OFF" AND REMOVE PLUG FROM POWER SOURCE
OUTLET BEFORE MAINTAINING OR LUBRICATING
YOUR SAW.

When

you

receive

your

new

Craftsman

radial

saw,

it

requires no lubrication. The radial saw has been partially
aligned and all bearings are lubricated and sealed for life. In

time,

however,

in

order

to

keep

your

saw

in

perfect

working order and accurate, it will be necessary to lubricate

and realign. In fact, your radial saw needs more of a
cleaning than a lubrication.

Make sure the teeth of the ANTI KICKBACK pawls are
always sharp, Replace if not sharp.

LUBRICATION

Your saw is precision built and should be kept clean and
properly

lubricated.

Before

describing

the

various

points

which

may

periodically

require

lubrication,

IT

IS

MORE

IMPORTANT

TO

FIRST

MENTION

THE

VARIOUS

POINTS WHICH SHOULD NOT BE LUBRICATED.

NO LUBRICATION REQUIRED

Do not lubricate carriage ball bearings or motor bearings as
these

are

sealed

ball

bearings

and

require

no

added

lubrication.

Do not lubricate between radial arm cap and radial arm.

PERIODICALLY LUBRICATE THESE POINTS

Use SAE No, 10W-30 automotive engine oil and refer to

Parts List for locations. Apply a few drops of oil along the
swivel latch pin and bevel index pin only if the pin has a
tendency to stick. Remove the left-hand carriage cover and

use oil sparingly to prevent it from getting on the ball
bearings or races.

A light film of oil should be wiped on the face of the
column tube to lubricate the fit between the column tube,
and column support.

The

thread

on

the

elevation

shaft

assembly

can

be

lubricated through the oil hole in the center of the radial
arm cap.

CAUTION:

Excessive oil at any location will attract

airborne dust particles and sawdust.

recommended accessories

ITEM

CAT.NO,

Stand ......................................................................................... 9-22205
Steel Legs .................................................................................. 9-22238
Casters ............................................................ 9-22221 or 9-22222
Drill Chuck & Key ....................................................................... 9-2980

’^Molding Head Guard — 7-inch ................................................ 9-29524
‘Molding Head Guard — 8-inch .................................................. 9-29523

Rotary Surface Planer — Carbide Tip ...................................... 9-29513

Sanding Wheel — 8-inch ............................................................ 9-2274
Sanding Wheel - 10-inch ........................................................... 9-22723

Dust Collector ............................................................................ 9-16997

Taper Jig....................................................................................... 9-3233

*Satin Cut Dado

7-inch......................................... 9-3257

‘Satin Cut Dado

8-inch ......................................... 9-3253

‘Molding Head Single

Cutter ........................................ .. 9-3215

‘Molding Head Three

Cutter ................................................ 9-3221

Sanding Drum — 3-inch ............................................................ 9-25246

• Lower Retractable Guard ........................................................... 9-29009

"Power Tool Know How Handbook"

Radial Saw...............................................................................9-291 7

‘Before purchasing or using any of these accessories, read

and

comply

with

additional

safety

instructions

No.

"(D)2"

on

p.

5 of this manual.

The above recommended accessories are current and were
available at the time this manual was printed.

• Meets OSHA Requirements as of 8-73.

NOTE: This lower retractable guard is designed to provide

additional protection to the operator in an axial direction

to

the

sawblade

(perpendicular

to

the

plane

of

the

sawblade):

(a)

When NOT in the cut (guards in full down position

(touching the table) and carriage in full rear position

behind fence):

(b)

When saw is set up to perform 90° crosscut operations

(sawblade 90° to table surface and arm in 90° crosscut

position).

34