Philips FW-C700 - Manual (Page 35)

Preparativos
Conexiones posteriores
La placa de especificaciones está situada
en la parte posterior de su sistema.
Power
Antes de conectar el cable de alimentación de
CA a la toma de corriente de pared, asegúrese
de que todas las demás conexiones hayan sido
realizadas.
Conexión de antenas
Conecte la antena de cuadro de AM y antena de
FM al terminal respectivo. Ajuste la posición de la
antena de forma que se obtenga una recepción
óptima.
Antena de AM
¡ADVERTENCIA!
- Para obtener un rendimiento óptimo, as
utilice solamente el cable de alimentación
original.
- Nunca haga ni cambie conexiones con la
corriente activada.
Para evitar sobrecalentar el sistema, se ha
incorporado un circuito de seguridad. Por
consiguiente, su sistema puede pasar
automáticamente al modo de espera bajo
condiciones extremas. Si ocurre esto,
permita que el sistema se enfríe antes de
volver a utilizarlo (no disponible para todas ¡as
versiones).
• Posicione la antena lo más apartada posible de
uniyVCR u otras fuentes de radiación.
Clock/Timer
Press CD, TUNER or TAPE to select the
desired source.
Before setting timer make sure the music source
has been prepared.
CD - Load the disc(s).To start from a specific
track, make a program (refer to “CD Operation -
Programming the disc tracks”).
TUNER - tune to the desired radio station.
TAPE - load the prerecorded tape into tape
deck 2.
Press « or ►► on the system repeatedly to set
the hour for the timer to start
Press M or ►! on the system repeatedly to set
the minute for the timer to start.
Press CLOCK‘TIMER to store the start time.
"Tli'iCf? uf-l" will be displayed and followed
by the set timer ";c; :i; ,'i" and then the selected
source.
-» TIMER © will remain on the display.
At the preset time, the selected source will play.
To exit without storing the setting
• Press ■ on the system.
To activate the TIMER
Press TIMER ON/OFF on the remote control.
-♦ The last set timer information will be shown
for a few seconds and timer © will appear on
the display.
Sleep Timer Setting
The sleep timer enables the system to switch to
Standby mode automatically at a preset time.
Notes:
- If the selected source (CD) is not available when
preset timer is reached,TUNER will be selected
automatically.
- During timer setting, if no button is pressed
within 90 seconds, the system wilt exit timer setting
mode automatically.
To deactivate the TIMER
Press TIMER ON/OFF on the remote control.
The display will show 'tRifCilL" and timer ©
will disappear from the display.
Press SLEEP on the remote control repeatedly
to select a preset time.
The selections are as follows (time in
minutes):
IS-TD-WS-ELl-Orr- 15 ...
“SLEEP f'f"' or"f]EE" will be displayed,
is the time in minutes.
When you reach the desired length of time, stop
pressing the SLEEP button.
SLEEP will appear on the display, except for
"uEE" mode.
The SleepTimer is now set. Before the
system switches to standby mode, a countdown
of 10 seconds will be displayed.
'SLEEP
- "5LEEF
■"SLEEP 3".,..- "SLEEP
While SLEEP mode is activated
To check the remaining length of time
Press SLEEP once.
To change the preset sleep timer
Press SLEEP twice.
The display will show the remaining time
followed by the sequence of sleep timer options.
To deactivate the SleepTimer
Press SLEEP repeatedly until "355" is displayed,
or press the STANDBY ON button.
60 25