Specifications i glossary 55 specifications, Glossary, General – Philips CCZ194AT User Manual
Page 55: Tuner broadcast channels, Cable tv channels, Terminals, Electrical specifications, Audio lack, Automatic channel setup, Bands
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Specifications I Glossary 55
Specifications
General
CRT: 19-inch in line gun
Television system: NTSC-M
Closed caption system: Section 15.119, FCC
(Federal Communications Commission) Standard
Video Heads: Four heads
Tape width: 1/2 inch (12.65 mm)
Tape speed
SP: 33.35 mm/sec.
LP: 16.67 mm/sec.
SLP: 11.12 mm/sec.
Operating Temperature: 4 l°F (5°C) to I04°F (40°C)
Relative Humidity: 10% to 75%
Power requirement: AC 120V, 60Hz
Power consumption: 90W
Sound output: IW
Dimensions:
19-11/16" (H) X 19-7/16" (W) X 18-5/16" (D)
500 mm x 494 mm x 465 mm
Weight: 44.1 lbs (20 kg)
Tuner Broadcast Channels
VHF 2-l3,UHF 14-69
Cable TV Channels
Midband:A - I
Superband: J -W
Hyperband: A-5 - A-1
Special Channel: 5A
Ultraband: 37 - 94, 100-125
Terminals
Antenna IN:VHF/UHF 75 ohms unbalanced
Video IN: RCA connector
Audio IN: RCA connector
Earphone: 3.5 mm CES
Electrical Specifications
Video input level: 0.5~2.0Vp-p
Audio input leveh-IOdBv
Video S/N ratio
SP: More than 42dBp
Audio S/N ratio
SP: More than 38dB
Designs and specifications are subject to change without
notice and without our legal obligation.
Glossary
AUDIO lack:
jack located on the front of the
TV/VCR which is used to record audio from anoth
er source.
Automatic Channel Setup:
process in which the
TV/VCR scans all available channels and places the
ones you receive in its memory.Then, when you
push the CH(annel). Up/Down buttons, you only
scan through channels you receive.
Bands:
settings that allow you to tune channels.
• Antenna
- VHF (very high frequency; channels 2
- 13) and UHF (ultra high frequency; channels 14 -
69).
• Cable
- all standard channels can be received
without a Cable Box.
Brightness:
adjusting increases or decreases the
brightness of the color on-screen.
Color:
adjusting pales or brightens the TV/VCR color.
Dubbing:
copying a tape using a VCR.
HO:
high quality; a feature in the TV/VCR circuitry
which provides enhanced picture detail.
Line Input:
The channel to which you set your
TV/VCR during dubbing.The line input channel is
always channel 00 (A/V IN).
Mode:
a TV/VCR operation.
OTR:
One-Touch Recording; programming a timed
recording that starts immediately and records for
30 minutes to eight hours, whichever you specify.
Picture:
adjust to increase or decrease the con
trast of the picture on-screen.
Sharpness:
adjusting softens or clarifies the picture
on-screen.
Tape Speeds:
how fast the tape travels during
playback or recording.
• SP
(standard play) - fastest tape speed (record
ing time for a T120 tape is approximately two
hours); best picture quality.
• LP
(long play) - average tape speed (recording
time for a T120 tape is approximately four
hours).
• SLP
(super long play) - slowest tape speed
(recording time for a T120 tape is approximately
six hours).
Tint;
adjusting changes the tints of the picture on the
TV/VCR from purple to green.
VCR:
video cassette recorder.
VIDEO lack:
jack located on the front of the
TV/VCR which is used to record video from anoth
er source.