Futaba FX-40 - Manual (Page 125)

125
EXP1 curve adjustment
Rate A and Rate B can be adjusted separately
or simultaneously. The EXP curves rate (EXP
A, EXP B) can also be adjusted separately or
simultaneously.
>6HWWLQJPRGHV@
* [ S e p a r a t e ] m o d e :
5DWHV DUH DGMXVWHG
separately.
*[Combined] mode: 5DWHV DUH DGMXVWHG
simultaneously.
>6HWWLQJPHWKRG@
1. Select the setting mode.
2. Touch the button of the rate or EXP curve
rate your want to set.
8VHWKHDGMXVWPHQWEXWWRQVWRVHWWKHUDWH
*Initial value: +100.0% (rate), +0.0 (EXP rate)
The curve can also be horizontally offset in the
vertical direction.
>2IIVHWWLQJWKHFXUYHKRUL]RQWDOO\LQWKHYHUWLFDO
GLUHFWLRQ@
7RXFKWKH2IIVHWEXWWRQ
8VH WKH DGMXVWPHQW EXWWRQV WR PRYH WKH
FXUYHKRUL]RQWDOO\XSRUGRZQ
*Initial value: +0.0
(EXP1 curve)
ŏ8 V L Q J W K H ( ; 3 F X U Y H L V K H O S I X O L Q
smoothening starting of the ailerons,
elevators, rudder, etc.
(EXP2 curve)
ŏ8VLQJWKH(;3FXUYHLVKHOSIXOLQHQJLQH
rise and other engine control.
VTR curve adjustment
Rate A and Rate B can be adjusted separately or
simultaneously. The VTR curve point positions (P.
Pos. A, P. Pos. B) and rates (P. Rate A, P. Rate B)
can also be adjusted separately or simultaneously.
>6HWWLQJPRGHV@
*[Separate] mode: Positions and rates are
DGMXVWHGVHSDUDWHO\
*[Combined] mode: Positions and rates are
DGMXVWHGVLPXOWDQHRXVO\
>6HWWLQJPHWKRG@
1. Select the setting mode.
2. Touch the button of the rate or VTR curve
point position (or rate) you want to set.
8VH WKH DGMXVWPHQW EXWWRQV WR VHW WKH 975
curve point position (or rate).
,QLWLDOYDOXHV5DWH33RV$
33RV%35DWH
The curve can also be offset horizontally in the
vertical direction.
>2IIVHWWLQJWKHFXUYHKRUL]RQWDOO\LQWKHYHUWLFDO
GLUHFWLRQ@
7RXFKWKH2IIVHWEXWWRQ
8VH WKH DGMXVWPHQW EXWWRQV WR PRYH WKH
FXUYH KRUL]RQWDOO\ XS DQG GRZQ ZLWK WKH
DGMXVWPHQWEXWWRQV
*Initial value: +0.0%
(VTR curve)
ŏ6HWWLQJLVIDVWLIOHIWULJKWXSDQGGRZQ
DUHÀUVWGHFLGHGLQWKH&RPELQHGPRGH
and the mode is then switched to the
Separate mode.
When this curve is used when the control
surface angle is large such as with
acrobatic models, switching from normal
flight to acrobatic is performed without
switch operation.