Futaba FX-40 - Manual (Page 100)

100
ŏ5HWXUQWR0RGHO0HQX
*\UR >&RUUHVSRQGLQJPRGHOW\SH@$LUSODQHJOLGHUJHQHUDO
7KLVIXQFWLRQLVXVHGZKHQD*<$6HULHVJ\UR
is used to stabilize the fuselage attitude. The
VHQVLWLYLW\DQGRSHUDWLRQPRGH1RUPDOPRGH*<
mode) can be changed with a switch.
ŏ7KUHHUDWHV5DWH5DWH5DWHFDQEH
switched.
ŏ8SWRD[HV*\UR*\UR*\URFDQEH
simultaneously controlled.
*Initial setting does not assign a sensitivity channel. Use the
ŏ7RXFKWKH>*\UR@EXWWRQLQWKH0RGHO0HQX
to call the setup screen shown below.
Function menu of the Linkage Menu to assign the sensitivity
FKDQQHO *\UR*\UR*\UR XVHG WR D YDFDQW FKDQQHO
beforehand.
Set [ACT] and [Trim] other than Function to [NULL].
ŏ7KHRSHUDWLRQPRGH$9&6125DQGVHQVLWLYLW\RI
the 3 axes Gyro/Gyro2/Gyro3 can be set.
ŏ *URXSVLQJOH PRGH VZLWFKLQJ
(Gr./Sngl)
(For more information, see the description
at the back of this manual.)
ŏ7KUHHUDWHV5DWH5DWH5DWHFDQEHXVHG
ŏ7RXFKWKH$&7EXWWRQRIWKHUDWHWREHXVHGDQGVHWWKHIXQFWLRQWR
$&7>21@RU>2))@
ŏ :KHQ D )XWDED *<$ J\UR LV XVHG ZKHQ >*<@ W\SH LV V HOHFWHG WKH
VHQVLWLYLW\VHWYDOXHLVGLUHFWO\UHDGLQERWKWKH$9&6DQG125PRGHV
ŏ :KHQ VHWWLQJ D VZLWFK WRXFK WKH VZLWFK EXWWRQ WR FDOO WKH 6ZLWFK!
VFUHHQDQGWKHQVHOHFWWKHVZLWFKDQGVHWLWV21GLUHFWLRQ
(For a description of the switch selection method, see the description at
the end of this manual.)
([DPSOH6HWWLQJD[HVXVLQJD*<$DQG*<$D[HVJ\UR
ŏ:LQJW\SH$LOHURQVHUYRVPRXQWHGIXVHODJHVHOHFWHG
ŏ6HW*\UR*<$&+*\UR*<$&+*\UR*<$&+DWWKH
)XQFWLRQPHQXRIWKH/LQNDJH0HQX
ŏ5DWH>2))@>*<@>6:(@>125@>@>125@>@>125@> @>*U@
5DWH>,1+@>*<@>18//@>$9&6@>@>$9&6@>@>$9&6@>@>*U@
5DWH>2))@>*<@>6((@>$9&6@>@>$9&6@>@>$9&6@>@>*U@
*When separating the conditions, set to [Sngl].
6HWVRWKDW5DWHLVWXUQHGRQDWWKHEDFNSRVLWLRQRIVZLWFK(DQG5DWHLVWXUQHG21DWWKH
front position.
Since switch E is turned OFF at the center, Rate 2 remains [INH].