Futaba 8FGAS, 8FGHS 2.4GHz - Manual (Page 44)

44
TRAINER Trainer system starting and setting
The Trainer function makes it possible for the
instructor to choose which functions (*1) and channels
are to be used for instruction, making it possible to
match the training ability to the student's skill level.
Two transmitters must be connected by an optional
trainer cord, and the instructor's transmitter should
be programmed for trainer operation, as described
below.
When the Instructor activates the trainer switch,
the student has control of the aircraft (if MIX or
FUNC mode is turned on, the Instructor can make
corrections while the student has control). When
the switch is released the Instructor regains control.
This is very useful if the student gets the aircraft
into an undesirable situation.
You can select the channel input data from the
student transmitter as either "FUNC" or "MIX"
mode. These options make it easier to use a variety
of receivers, transmitters, etc.
It is also possible to use the virtual channel (VC)
at “FUNC” or “MIX” mode or to use the trainer
system with flying wing airplanes.
When using T8FGS as the student transmitter,
the trainer function is not used.
(*1) You can select the operation mode for each channel.
(NORM/MIX/FUNC/OFF)
NOTE: This trainer system can be used in the
following manner;
1. With the T8FGS transmitter and a conventional
transmitter, if the channel order is different,
it is necessary to match the channel order
before using this function.
You can select the channel of input data
from student's transmitter in the "FUNC" or
"MIX" mode.
2. When the T8FGS is used as the instructor’s
transmitter, set the modulation mode of the
student’s transmitter to PPM.
If being used as the student, T8FGS can be
connected to the instructor's transmitter which
the PPM mode as the student's modulation
mode is required. T8FGS always sends PPM
mode signal from the trainer jack.
3. Be sure that all channels work correctly in
both transmitters before flying.
T8FGS/T8FG/T12FG special trainer cable
Use the T8FGS/T8FG/T12FG special trainer cable (FUTM4405) when using the T8FGS,
T8FG or T12FG transmitter at the trainer function instructor side. Operation may not be
normal with a conventional trainer cable.
*If the T8FGS, T8FG or T12FG transmitter is used as the student transmitter when the instructor transmitter is
not a T8FGS, T8FG or T12FG, a conventional trainer cable may be used.
Instructor Student Trainer cable
T8FGS, T8FG,
T12FG, FX-20
T4EX, T6EX, T7C, T9C, T10C T12FG special trainer cable
T8FGS, T8FG, T12FG, T12Z,
T14MZ, FX-40, FX-20
Conventional trainer cable (Rect. - Rect.)
T4V Conventional trainer cable (Rect. - Round)
T6X, T7U, T8U, and T9Z are not applicable.
Other than
T8FGS, T8FG,
T12FG, FX-20
T8FGS, T8FG, T12FG, FX-20
Conventional trainer cable (Rect. - Rect.) or
Conventional trainer cable (Rect. - Round)
*The direction that the T8FGS/T8FG/T12FG special trainer cable connects is fixed.
Connect the instructor cable adapter connector of the cable to the instructor T8FGS, T8FG or
T12FG and connect the student connector to the student transmitter. If the cable is connected
in reverse, the student's transmitter power will not be turned on even if the instructor side
power is set to ON.
*If the instructor side T8FGS, T8FG or T12FG trainer function is not enabled, the
student's power will not be turned ON even if the connection direction is correct.