Flintec FT-12 Manual - Manual (Page 43)

FT-12 Technical Manual, Rev. 1.35 November 2010 Page 43 of 44
A PPENDIX 6: P ARAMETER ’ S D EFAULT T ABLE
Parameter Factory defaults
0-- Interface
00- Serial Interface 1
0 Data format 2 = Printer
1 Baud rate 3 = 9600
2 Handshake 0 = Disable
3 Address 0
4 Data length and parity 0 = 8 bit, no parity
5 Checksum 1 = Enable
01- Serial Interface 2
10 Data format 0 = Disable
11 Baud rate 3 = 9600
12 Handshake 0 = No
13 Address 0
14 Data length and parity 0 = 8 bit, no parity
15 Checksum 1 = Enable
02- Serial Interface 3
20 Data format 0 = Disable
21 Baud rate 3 = 9600
22 Handshake 0 = Disable
23 Address 0
24 Mode 0 = RS232C
25 Data length and parity 0 = 8 bit, no parity
26 Checksum 1 = Enable
03- Ethernet / Profibus
30 Ethernet data format 0 = Disable
31 Ethernet address 0
04- Printer
40 Print out format 2 = Multi line
41 Date & Time 1 = Will be printed
42 CN (Consecutive number) 1 = Will be printed
43 ID1 0 = Won’t be printed
44 ID2 0 = Won’t be printed
45 Minimum print 20 kg
46 Print control 0 = With Print Key
47 Line feed 11 = 1 LF + 1 LF
48 Form feed 0 = No
49 Quantity of copies 1
1-- Configuration
10- Application
100 Mode 0 = Basic weighing
101 Threshold weight 100 kg
102 Ending rate 50%
103 Period (Dynamic) 9.9 s
104 Alarm 0 = Disable
105 Filling type 0 = Gross
11- Start Up
111 Auto power off 0 = Disable
112 Store Tare at power off 0 = Disable
113 Auto tare clear 0 = Disable
114 Buzzer active? 0 = Disable
12- Filter
120 Filter 7
13- Digital I/0
130 Outputs 0 = Disable
131 Input 1 0 = Disable
132 Input 2 0 = Disable
133 Input 3 0 = Disable
14- Entries
140 Date entry dd.mm.yy
141 Time entry hh.mm
142 Label no. entry
Parameter Factory defaults
2-- Scale Parameters
20- Set up
200Approved 0 = No
201Increased indication 0 = With x10 key
202Power on zero 2 = ± %10
203Zero with key 1 = ± %2
204Auto zero tracking 0 = Disable
205Tare 1 = With Tare Key
206Motion detector 1 = ± 0,5e
207Tilt switch 0 = Disable
208Stability time 0.0 s
21- Scale Build
210Scale Type 0 = Single Range
211Capacity 1 / d1
212Capacity (2) / d(2) 6 kg / 1 g
3-- Calibration / Adjustment
30- Calibration
300Gravity
301Calibration
31- Adjustment
310Zero adjustment
311Span adjustment
312Span adjustment under load
4-- Analogue Output
40- Signal Selection
400Analogue Output Signal Type
41- Zero Adjustment
410Coarse Zero Adjustment
411Fine Zero Adjustment
42- Span Adjustment
420Coarse Span Adjustment
421Fine Span Adjustment
8-- Metrological Data
80- Legal Metrology
800Calibration counter
801Alibi memory
802Calling a record
803Print Alibi memory
804Alibi memory information
9-- Diagnostics
90- Tests
900Key Pad test
901Serial interface 1 test
902Digital input test
903Digital output test
904mV indication
91- Serial numbers
910FT-1x serial no.
911Option 1 serial no. (if installed)
912Option 2 serial no. (if installed)
913Option 3 serial no. (if installed)
97- Calibration coefficients
97X Calibration coefficients
99- Print
Parameters
990All parameters
991Load default parameters