Dynaflite DYFA1009 - Manual (Page 4)

Engine Mount (DAVG3005)
Propellers - Refer to your engine's instructions
for proper size
1 roll of Covering Film; See Covering Tips
(page 30)
1 /4" Latex Rubber Padding (HCAQ1000)
1/16" Foam Wing Seating Tape (GPMQ4422)
(2) 1-1/2" Wheels (GPMQ4243)
(2) 3/32" Wheel Collars (GPMQ4302)
#64 Rubber Bands (1 /4 Ib box - HCAQ2020)
(4) #2 x 3/8" Screw for mounting your engine
Self-Adhesive Lead Weight (GPMQ4485)
*lf your radio includes a "flat" style battery for the
receiver, ask your hobby dealer if you can swap it
for a square style. The square style battery fits in the
fuselage better than a flat one.
CA Activator - (GPMR6035)
30-Minute Pro Epoxy - (GPMR6047)
#1 Hobby Knife Handle (XACR4305)
#11 Blades (Qty. 100 - HCAR0311) or
(Qty.5-XACR2911)
Hobbico (or similar) Builders Triangle
(HCAR0480)
Medium T-pins (HCAR5150)
Wax Paper
Electric Drill
Drill Bits: 1/16", 3/32"/ 1/8"/ 3/16
11
Masking Tape
String for aligning the stabilizer
#1 Phi Hips Screwdriver
Top Flite Covering Iron (TOPR2100)
A building board that you can stick pins into
(see "Setting Up Shop")
SETTING UP SHOP
If this is your first model there are a few supplies and
tools that you should gather before you begin. The
most important item is a flat table that you can build
your models on. You can turn a solid core door into
a building table, but avoid hollow core doors
because they warp easily. If possible, locate your
building table in an area that is not in the way of
other projects or household activities. Cover your
building table with a board that you can stick pins
into. The back of a 2' x 4' ceiling tile works well or
you can cut a piece to fit your table from a 4' x 8'
sheet of Celotex insulation board available from a
home improvement store.
REQUIRED SUPPLIES
AND TOOLS
These are the building tools and adhesives that you
will need to build your Piece 0' Cake.
We recommend Great Planes Pro™ CA and Epoxy
2 oz. Thin CA Adhesive - (GPMR6003)
2 oz. Medium CA+ Adhesive (GPMR6009)
OPTIONAL ACCESSORIES
Razor Plane (MASR1510)
Single-Edge Razor Blades (100, HCAR0312)
CA Applicator Tips (HCAR3780)
Hot Sock™ (for your covering iron, TOPR2175)
6-Minute Pro Epoxy (GPMR6045)
Trim Seal Tool™ (TOPR2200)
Heat Gun (TOPR2000)
Straightedge (Fourmost Non-Slip, FORR2149)
Denatured or IsopropyI Alcohol (for epoxy
clean-up) '
HobbyLite™ Balsa Filler (HCAR3401)
Epoxy Brushes (GPMR8060)
CA Debonder (GPMR6039)
Powered hand tool with Sanding Drum and
Cut-off Wheel
Bar Sander or Sanding Block and Sandpaper
(coarse, medium, fine grit)*
Microballoons Filler (TOPR1090)
You can build your Piece 0' Cake without these items
but they will make the job much easier and provide you
with better results. These are things you will accumulate
as your building "career" progresses anyway.
4