KEYENCE XG-8000 Series - Manual (Page 7)

7
Standard Specifications
The following values show the terminal block 1 specifications for the system.
Tightening with a force above the standard torque may cause damage to the
terminal block.
OUT1 connector
• Socket block: MC1.5/9-ST-3.5BK
(Phoenix Contact)
• Compatible electric wires:
AWG16 to 28
• Terminal block screw torque:
0.25 N·m or less
IN1 connector
• Socket block: MC1.5/6-ST-3.5BK
(Phoenix Contact)
• Compatible electric wires:
AWG16 to 28
• Terminal block screw torque:
0.25 N·m or less
Pin Settings
OUT1 connector
IN1 connector
*1 Initial assignment status is a status that system variables are assigned to
each terminal by the initial environment settings value. This may be
different from the original description due to setting change.
*2 For more details on each variable function, see the "List of System
Variables" of XG VisionEditor reference manual.
• Power source 0 V and COMIN1, COMIN2 (Connector), COMIN2 (Terminal
block), COMOUT1, COMOUT2, COMOUT_F+, COMOUT_F-,
COMOUT2_F+, COMOUT2_F-, and 0VOUT are all isolated.
• COMOUT1 is the common terminal for output terminals 1 and 2.
• COMOUT_F+ and COMOUT_F- are the common terminal for output
terminals 3, 4 and 6, 7.
• COMIN1 is the common terminal for input terminals 2 through to 6.
Standard Specifications
The following values show the terminal block 2 specifications for the system.
Tightening with a force above the standard torque may cause damage to the
terminal block.
OUT2 connector
• Socket block: MC1.5/8-ST-3.81BK
(Phoenix Contact)
• Compatible electric wires:
AWG16 to 28
• Terminal block screw torque:
0.25 N·m or less
IN2 connector
• Socket block: MC1.5/6-ST-3.5BK
(Phoenix Contact)
• Compatible electric wires:
AWG16 to 28
• Terminal block screw torque:
0.25N·m or less
Pin Settings
IN2 connector (XG-8500L(P)/8502L(P)/8700L(P)/8702L(P)/
8800L(P)/8802L(P))
IN2 connector (XG-8800(P)/8802(P))
OUT2 connector
*1 Initial assignment status is a status that system variables are assigned to
each terminal by the initial environment settings value. This may be
different from the original description due to setting change.
*2 For more details on each variable function, see the “List of System
Variables” (Settings Issue) of the XG VisionEditor reference manual.
Terminal Block 1
No.
Name
Terminal ID is noted in ( )
Reference
Initial assignment status *1
Circuit
diagram
Variable function *2 Bit
1 OUT22 (STO) Output 22
I/O terminal/
Parallel I/O output
change strobe
0 D
2 OUT23 (OR) Output 23
Outputs the total
status output
0 D
3 F_OUT2 (ERR) High speed output 2 Error 0 output 0 C
4 F_OUT3 (RUN) High speed output 3 Run mode output 0 C
5
COMOUT1
(COMOUT) Common for terminal
block output (1, 2)
– – –
6 F_OUT0 (FLS1) High speed output 0 Strobe output 1 0 C
7 F_OUT1 (FLS2) High speed output 1 Strobe output 2 0 C
8
COMOUT1_F+
(COM1F+)
Common for high
speed output (+)
(3, 4 and 6, 7)
– – –
9
COMOUT1_F-
(COM1F-)
Common for high
speed output (-)
(3, 4 and 6, 7)
– – –
No.
Name
Terminal ID is noted in ( )
Reference
Initial assignment status *1
Circuit
diagram
Variable function *2 Bit
1 COMIN1 (COMIN1)
Common for terminal
block input
– – –
2 IN15 (PLC) Input 15
Custom command
execution input (PLC)
0 B
3 F_IN0 (TRG1) High speed input 0 Trigger 1 input 0 A
4 F_IN1 (TRG2) High speed input 1 Trigger 2 input 0 A
5 F_IN2 (TEST) High speed input 2 Test run input 0 A
6 F_IN3 (EXT) High speed input 3 Disable trigger input 0 A
Note
6
Reference
Note
Terminal Block 2 (XG-8500L(P)/8502L(P)/
8700L(P)/8702L(P)/8800(P)/8802(P)/
8800L(P)/8802L(P) only)
No.
Name
Terminal ID is noted in ( )
Reference
Initial assignment status *1 Circuit
diagram
Variable function *2 Bit
1 F_IN4 (ENCA+)
RS-422 Encoder
Input A+ Assignment not
possible
– –
2 F_IN4- (ENCA-)
RS-422 Encoder
Input A- Assignment not
possible
– –
3 F_IN5 (ENCB+)
RS-422 Encoder
Input B+ Assignment not
possible
– –
4 F_IN5- (ENCB-)
RS-422 Encoder
Input B- Assignment not
possible
– –
5 F_IN6 (ENCZ+)
RS-422 Encoder
Input Z+ Assignment not
possible
– –
6 F_IN6- (ENCZ-)
RS-422 Encoder
Input Z- Assignment not
possible
– –
7 5VOUT 5VOUT – – –
8 0VOUT 0VOUT – – –
No.
Name
Terminal ID is noted in ( )
Reference
Initial assignment status *1
Circuit
diagram
Variable function *2 Bit
1 F_IN4 High-speed Input 4 No Initial Assignment – A
2 F_IN5 High-speed Input 5 No Initial Assignment – A
3 F_IN6 High-speed Input 6 No Initial Assignment – A
4 F_IN7 High-speed Input 7 No Initial Assignment – A
5 IN16 Input 16 No Initial Assignment – B
6 IN17 Input 17 No Initial Assignment – B
7 COMIN2
Common for terminal
block Input
– – –
8 – Not in use – – –
No.
Name
Terminal ID is noted in ( )
Reference
Initial assignment status *1 Circuit
diagram
Variable function *2 Bit
1 F_OUT4 (FLS5) High-speed Output4 No Initial Assignment – C
2 F_OUT5 (FLS6) High-speed Output5 No Initial Assignment – C
3 F_OUT6 (FLS7) High-speed Output6 No Initial Assignment – C
4 F_OUT7 (FLS8) High-speed Output7 No Initial Assignment – C
5
COMOUT2_F+
(COM2F+) Common for
High-speed Output (+)
– – –
6
COMOUT2_F-
(COM2F-) Common for
High-speed Output (–)
– – –
Note
Reference