KEYENCE FS-10 - Manual (Page 4)

4
Specifications are subject to change without notice.
KEYENCE CORPORATION
1-3-14, Higashi-Nakajima, Higashi-Yodogawa-ku,
Osaka, 533-8555, Japan
PHONE: +81-6-6379-2211
Copyright (c) 2010 KEYENCE CORPORATION. All rights reserved.
11225E 1080-1 96M11225
Printed in Japan
A7WW1-MAN-0069
• The required adaptor is included in each model of the FU series. If
an inadequate adaptor is used, the fiber unit cannot be properly
installed.
• To connect the coaxial reflective type fiber unit to the amplifier,
connect the single-core fiber to the transmitter side, and connect the
multiple-core fiber to the receiver side.
(Connect the fibers according to the marking on the amplifier lateral
side.)
HINTS ON CORRECT USE
• To extend the cable length, use a cable with at
least a 0.3 mm 2 cross-section area. Limit the
length of cable extension to no more than 100
m. (To connect several units, contact Keyence
for further information.)
• If the amplifier cable is placed together with
power lines or high voltage lines in the same
conduit, detection error may occur due to
noise interference, or the sensor may be
damaged. Isolate the amplifier cable from
these lines.
• When using a commercially available
switching regulator, ground the frame ground
terminal and ground terminal.
• Do not use the FS series outdoors, or in a
place where extraneous light can enter the
light receiving surface directly.
• Due to the individual dispersion of
characteristics and the difference in fiber unit
model, the maximum sensing distance or
displayed value of all the units are not the
same.
• Improper wiring may cause the amplifier to
become hot or may change the sensitivity.
• The displayed value may vary depending on
the surrounding environment (change in
temperature, dust, etc.).
DIMENSIONS Unit: mm
1 9
2 18
3 27
4 36
5 45
6 54
7 63
8 72
9 81
10 90
11 99
12 108
13 117
14 126
15 135
16 144
17 153
No. of units L
End unit [included in FS-V12(P)]
CONNECTING FIBER UNIT
Lower the quick-release lever, insert the fiber unit about 14 mm until it
reaches the end, and then lift the quick-release lever.
• To connect a fiber unit with a small diameter, use the adaptor
included with the FU series.
1. Attach the adaptor to the fiber
unit.
2. Fully insert the adaptor into the
mounting holes of the amplifier,
and then lift the quick-release
lever.
Note: If the fiber unit is improperly connected, the sensor cannot meet
the specifications.
2 1
Fiber insertion
mark
1
2
2
Multiple-core Single-core
Transmitter
Receiver
Note: Be sure to use the end units to connect to the expansion units.
9
4
6.7
90
12
min.
(Maximum
when the
cover is
opened)
*ø3.9 3-core x
Brown/Blue/Black: 0.34 mm
2
Cable length: 2 m
(13)
(33)
0.7 3
28.5
35.4 20.7
66
DIN-rail mounting
When the mounting bracket
[included in FS-V11(P)] is attached:
8
16
9
36.5
0.7 3
3.8
22.8
30.8
25.6 25.4
12
min.
2 x ø3.4
Spot facing: ø6,
2.7 (d)
2 x (4.4 x 3.4)
Spot facing: ø7, 4 (d)
15
31
FS-V11(P)
When several units are connected:
FS-V12(P)
9
4
6.7
90
(13)
(33)
0.7 3
28.5
35.4 20.7
66
11
min.
ø2.6 single-core
x 0.34 mm
2
Cable length: 2 m
(Maximum
when the
cover is
opened) DIN-rail mounting
6
35.4
53.8
9.2
(22.6) 20.8
DIN-rail mounting
6 6 L
End unit 1. End unit 1.
FS-V10
9
4
6.7
90
(33)
0.7 3
28.5
35.4 20.7
66
(Maximum
when the
cover is
opened) DIN-rail mounting
Cable outer dia.
ш1.3
ш1.0
Adapter
Adapter A
(OP-26500)
Adapter B
(OP-26501)
Appearance
WARRANTIES (MUST ACCOMPANY THE PRODUCTS): KEYENCE, at its sole
option, will refund, repair or replace at no charge any defective Products within
1year from the date of shipment. Unless stated otherwise herein, the Products
should not be used internally in humans, for human transportation, as safety
devices or fail-safe systems. EXCEPT FOR THE FOREGOING, ALL EXPRESS,
IMPLIED, AND STATUTORY WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-IN-
FRINGEMENT OF PROPRIETARY RIGHTS, ARE EXPRESSLY DISCLAIMED.
KEYENCE SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR OTHER DAMAGES, EVEN IF DAMAGES RESULT FROM
THE USE OF THE PRODUCTS IN ACCORDANCE WITH ANY SUGGESTIONS OR
INFORMATION PROVIDED BY KEYENCE. In some jurisdictions, some of the
foregoing warranty disclaimers or damage limitations may not apply.