Hardware installation – Talkaphone ETP-402V Dual Button Emergency / Information Phone User Manual
Page 5
Hardware Installation
D. Installing ETP-103 Series Phones
Models ETP-103 and ETP-103V are designed to mount behind an elevator car
operating panel and require connection to a push button with LED capability on the
car operating panel.
1. Determine the position where you will mount the phone. Be sure the phone
speaker and microphone are placed directly behind the speaker grille in the car
operating panel or mounting surface.
2. Mark the four mounting holes. Weld four 0.16” diameter threaded studs to these
spots. These studs should form a rectangle that is 7.2”h x 3.0”w. (Note: These
studs are usually pre-welded in place by the car operating panel manufacturer.)
3. Place the phone onto the studs and secure with nuts.
4. Plug the RJ11 connector on the cable extending from the unit into an RJ11
receptacle connected to the phone line (red is ring, green is tip).
5. Connect the Brown and Black wires to the phone activation switch. The Black
wire is the common wire.
6. Connect a Red wire and the Black wire to the LED. The phone comes with two
red wires, to operate two LEDʼs simultaneously if necessary. (Note: If LED does
not work, reverse polarity.)
Figure 1. Wiring an ETP-103 or ETP-103V to Elevator "Push to Talk" Pushbuttons
NOTES:
1) Many elevator car operating panel manufacturers "push to talk" buttons
use an LED manufactured by Data Display Products (part number 5SB-RLP2).
One is packed with the unit.
2) When inserting the LED into the button, be sure that the plus side of the LED
is connected to the red wire of the phone.
3) Models ETP-103 and ETP-103V are designed to connect to either one or two
Car Stations (i.e., one on each side of door). If you are only connecting to one
button, tape up the second set of wires to prevent shorting.
4) At the Branch's discretion the "alarm" push button can be used in lieu
of the "push to talk" pushbutton.
5) The above applications MUST be approved by the local code authority inspector.
REAR VIEW OF SWITCH
BROWN
BLACK
RED
- ETP-402KV Keypad Emergency Phone ETP-402KSV Keypad Access Phone ETP-400 MOD Single Button OEM Emergency Phone ETP-402KSEV Keypad Access Phone ETP-402KSE Keypad Access Phone ETP-402KS Keypad Access Phone ETP-402K Keypad Emergency Phone ETP-402CV Dual Button Assistance / Information Phone ETP-402C Dual Button Assistance / Information Phone ETP-402 Dual Button Emergency / Information Phone ETP-401V Single Button Emergency Phone ETP-401P Swimming Pool Emergency Phone ETP-401CV Single Button Assistance Phone ETP-401C Single Button Assistance Phone ETP-401 Single Button Emergency Phone ETP-400V MOD2 Single Button OEM Emergency Phone ETP-400V MOD Single Button OEM Emergency Phone ETP-400V Single Button Emergency Phone ETP-400KV Keypad Emergency Phone ETP-400KSV Keypad Access Phone ETP-400KSEV Keypad Access Phone ETP-400KSE Keypad Access Phone ETP-400KS Keypad Access Phone ETP-400K Keypad Emergency Phone ETP-400H-NC Handset Emergency Phone ETP-400DV Dual Button Emergency / Information Phone ETP-400 Emergency Phone With One Button ETP-400DCV Dual Button Assistance / Information Phone ETP-400DC Dual Button Assistance / Information Phone ETP-400D Dual Button Emergency / Information Phone ETP-400CV Single Button Assistance Phone ETP-400C Single Button Assistance Phone ETP-400 MOD2 Single Button OEM Emergency Phone ETP-103V OEM Emergency Phone ETP-103 OEM Emergency Phone ETP-100MV Surface Mount Emergency Phone ETP-100MBV Surface Mount Emergency Phone ETP-100MB Surface Mount Emergency Phone ETP-100M Surface Mount Emergency Phone ETP-100EV Flush Mount Emergency Phone ETP-100EBV Flush Mount Emergency Phone ETP-100EB Flush Mount Emergency Phone ETP-100E Flush Mount Emergency Phone