Software programming – Talkaphone ETP-402V Dual Button Emergency / Information Phone User Manual
Page 11
Software Programming
K. PBX/Timing Configuration Codes
Command Function
*14*1*
MODE I: Sets Talk-A-Phone unit for Central Office Trunk Line (default)
*14*2*
MODE II: Sets Talk-A-Phone unit for PBX when an EC-8 Consolidator
is used
*14*3*
MODE III: Sets Talk-A-Phone unit for PBX when an EC-8 Consolidator
is not used
*17* …[minutes]*
Sets the conversation timer (1 – 4,320 minutes) (default is 12
minutes)
*18*…[ring cycles]*
Sets the number of ring cycles (1 – 9) before the Talk-A-Phone unit
aborts a call and either redials the primary number or switches to the
secondary number (default is 9 ring cycles)
*100*
0.5 second hang-up on busy or no answer (default on ETP-100
Series)
*101*
2.25 second hang-up on busy or no answer
1
(default on ETP-400
Series)
*102*
51ms on/off dialing speed (default)
*103*
102ms on/off dialing speed
1
*40* …[0 – 10]*
Sets delay before phone dials (0 – 10 seconds)
May be used to wait to obtain PBX dial tone (default is 2 seconds)
*53*
Sets the Talk-A-Phone unit to disconnect if the Guard Station is silent
for 60 seconds
*54*
Talk-A-Phone unit will not disconnect if Guard Station is silent (default)
*55*
Sets Talk-A-Phone unit to disconnect if the Guard Station is silent for 30
seconds
*21*
Configures Talk-A-Phone unit for use with a Rolm PBX or a Mitel PBX
*22*
Cancels *21* command (default)
1
Not available on ETP-100 Series phones.
You can configure your Talk-A-Phone unit for a variety of environments. For
example, if your communication line is a PBX extension, you must configure the
Talk-A-Phone unit to recognize the PBX system by programming the following
functions:
• Telephone line type (Mode II or III): *14*[2 or 3]*
• Number of ring cycles before the Talk-A-Phone unit aborts a call and either
redials the primary number or switches to the secondary number: *18*…[ring
cycles]*
• Talk-A-Phone unit disconnects after 30 seconds of silence, *55*
When the Talk-A-Phone unitʼs extension is setup as a "ringdown" or "hot line", the Talk-A-
Phone unit has to be programmed with a phone number: *13*…[5 digit number]*
(Example: *13*12345*).
- ETP-402KV Keypad Emergency Phone ETP-402KSV Keypad Access Phone ETP-400 MOD Single Button OEM Emergency Phone ETP-402KSEV Keypad Access Phone ETP-402KSE Keypad Access Phone ETP-402KS Keypad Access Phone ETP-402K Keypad Emergency Phone ETP-402CV Dual Button Assistance / Information Phone ETP-402C Dual Button Assistance / Information Phone ETP-402 Dual Button Emergency / Information Phone ETP-401V Single Button Emergency Phone ETP-401P Swimming Pool Emergency Phone ETP-401CV Single Button Assistance Phone ETP-401C Single Button Assistance Phone ETP-401 Single Button Emergency Phone ETP-400V MOD2 Single Button OEM Emergency Phone ETP-400V MOD Single Button OEM Emergency Phone ETP-400V Single Button Emergency Phone ETP-400KV Keypad Emergency Phone ETP-400KSV Keypad Access Phone ETP-400KSEV Keypad Access Phone ETP-400KSE Keypad Access Phone ETP-400KS Keypad Access Phone ETP-400K Keypad Emergency Phone ETP-400H-NC Handset Emergency Phone ETP-400DV Dual Button Emergency / Information Phone ETP-400 Emergency Phone With One Button ETP-400DCV Dual Button Assistance / Information Phone ETP-400DC Dual Button Assistance / Information Phone ETP-400D Dual Button Emergency / Information Phone ETP-400CV Single Button Assistance Phone ETP-400C Single Button Assistance Phone ETP-400 MOD2 Single Button OEM Emergency Phone ETP-103V OEM Emergency Phone ETP-103 OEM Emergency Phone ETP-100MV Surface Mount Emergency Phone ETP-100MBV Surface Mount Emergency Phone ETP-100MB Surface Mount Emergency Phone ETP-100M Surface Mount Emergency Phone ETP-100EV Flush Mount Emergency Phone ETP-100EBV Flush Mount Emergency Phone ETP-100EB Flush Mount Emergency Phone ETP-100E Flush Mount Emergency Phone