Kontron AT8242 - Manual (Page 19)

Product Description
3 AT8242
www.kontron.com
1.3 Board Specifications
Table 1-1:Board Specifications
Features Description
Dual Multicore Packet
Processor Units
Dual Cavium Networks OCTEON II CN68xx MIPS64 v2 processors, each with up to 32-cores at up to
1.5 GHz depending on maximum power configuration; Interlaken lanes x 4 between the two OCTEON
II processors
Memory
Eight (4 per processor) DDR3 DIMM sockets each supporting 32GB address range for up to 256GB for
both processors once 32GB VLP DIMMs are available
Up to 1333 MHz ECC DIMM
eUSB Flash drive (16GB/32GB) per OCTEON II processor
Ethernet Multilayer Switch
Broadcom BCM56842 320Gbps Ethernet Multilayer Switch.
Broadcom StrataXGS®IV high performance Ethernet Switch Architecture
The BCM56842 switch provides 18 integrated WarpCores (72 SerDes)
Each WarpCore is configurable to support the following options:
One 40G-KR4, Four 10G-KR1/XFI/SFI, One 10G-XAUI, Four 1000Base-X/SGMII
Managed by the Unit Computer through a PCIe x1 Gen1 (2.5 Gbps)
One 1000Base-X link to the Unit Computer
The switch represents the central point of the AT8242. It manages the connections to the NPUs, the
RTM, the IPMC, the UC, the base interfaces and the fabric interfaces.
I/O Interfaces
Front: 2x RS232 - RJ45 ports, one to each OCTEON II processor
Front: 1x RS232 - RJ45 port to the switch management processor
Front: 1x 10/100/1000Base-T via RJ45 port to switch management processor
Switch Management
Processor
Single core Freescale P2010 processor
Manages the Broadcom Ethernet switch through a PCIe x1 Gen1 (2.5 Gbps) lane
One serdes lane is routed between SM processor and Broadcom switch
SM processor connected to: 1GB DDR3 ECC SODIMM; redundant NOR flash support
Telco Clock Telco clock support provided
Rear Transition Module
(RTM)
Two RTM options:
RTM8242: 84 Gbps total available bandwidth; supports 8 SFP+ (FI) connectors, 4x GbE SFP (BI)
connectors;
RTM8940: up to 82Gbps: 2x 1G SFP (BI), 2x 40G QSFP (FI)* with LRM support, and optional Telco PLL
(incl. optional SyncE support).
* The second QSFP can be disabled to activate the 4x 10G SFP+ ports (FI)
IPMI Features
Designed with IPMC, Dual IPMB, IPMI v2.0
Extensive sensor monitoring and event generation on thresholds
Two redundant IPMI firmware with rollover
Serial over LAN (IPMI v2.0) connectivity to the two CN68xx processors and the Management
Processor
Standards Compliance
This blade is compatible with the following standards:
PICMG 3.0 R3.0 specification; PICMG 3.1 R1.0 specification; PICMG 3.1 R2.0 specification;
IPMI v2.0, and RoHS compliant
Mechanical Characteristics Single slot ATCA blade
Operation Power
Dual CN6880 1.2Ghz AAP with 32GB DDR3: Payload maximum 200W
Dual CN6880 1.0Ghz CP with 32GB DDR3: Payload maximum 155W
AT8242 Idle Power: 115W
AT8242 Management Power: <15W
RTM maximum power: <25W