Crestron electronic Green Light GLPS-HSW-FT - Manual (Page 40)

Crestron Commercial Lighting Design Guide
36
DALI
Products
The following products are part of a DALI system. In addition to the DIN-DALI-2, other Crestron DIN rail products are listed. These
products install in the same cabinet as the DIN-DALI-2. The DIN-AP2 processor connects with any of these products via Cresnet or
Ethernet.
DALI and DIN Rail Products
DIN-DALI-2 DALI Interface Module Page 36
DIN-1DIM4 4 Channel Dimmer Page 37
DIN-1DIMU4 4 Channel Forward/Reverse Phase Dimmer Page 37
DIN-8SW8 8 Channel High-Voltage Switch Page 38
DIN-8SW8I 8 Channel High-Voltage Switch with Trigger Inputs Page 38
DIN-4DIMFLV4 4 Channel 0-10V Fluorescent Dimmer Page 38
DIN-AP2 2-Series Control Processor Page 49
DIN-2MC2 2 Channel Bidirectional Motor Control Page 62
DIN-AO8 8 Output 0-10 V Analog Module Page 64
DIN-IO8 8 Versiport I/O Module Page 64
DIN-HUB Cresnet Distribution Hub Page 64
DIN-BLOCK 12 Port Cresnet Distribution Block Page 65
DIN-PWS50 50 Watt Cresnet Power Supply Page 65
DIN-DALI-2
The DIN-DALI-2 is a DALI interface for Crestron systems providing control of up to two individual DALI loops. Housed in a DIN rail
enclosure, the DIN-DALI-2 is a great low-profile Cresnet or Ethernet companion to the DIN-AP2 processor, or any 2-Series control
system. In addition to controlling the DALI data bus, it includes an integrated DALI power supply. The single-wire connectivity simplifies
both new and retrofit installations, and Power-over-Ethernet (PoE) versatility assists in situations with existing CAT5 infrastructure.
> Controls up to 128 DALI ballasts
> Cresnet or PoE communication for single wire installation
> Integrated DALI power supply
> Crestron DALI commissioning tool for easy setup
> Override input for emergency mode
DALI Power
DALI ballast controllers require power in addition to the high
voltage power provided to the ballasts. This power is provided via
the DALI wiring. The DIN-DALI-2 has a DALI power supply built in,
eliminating the need for a separate power supply. A supplemental
power supply can be added if needed, and an onboard switch
allows installers to easily choose the power source.
Power over Ethernet
The DIN-DALI-2 gets its own power either through Cresnet or Power over Ethernet (PoE). This simplifies wiring to the DIN-DALI-2
module. The power from Cresnet or PoE is then used to power the DALI controllers if the DALI power switch is set to “int”. All 128 DALI
ballast controllers can be powered in either Cresnet or PoE mode.
Power Requirements
PoE Requirements 13 watts (0.270 Amps @ 48 Volts DC), regardless of DALI POWER setting
Cresnet Power Usage 9 watts (0.375 Amps @ 24 Volts DC), DALI POWER switch set to “INT”
2 watts (0.08 Amps @ 24 Volts DC), DALI POWER switch set to “EXT”
Note: Unit will default to Cresnet power if both PoE and Cresnet power are present.
Environmental
Temperature 32° to 104°F (0° to 40°C)
Humidity 10% to 90% RH (non-condensing)
Heat Dissipation 44 BTU/Hr