Document Outline

• SECTION 1:ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
  • 1.01 Arc Welding Hazards
  • 1.02 Principal Safety Standards
  • 1.03 Declaration of Conformity
• SECTION 2:INTRODUCTION
  • 2.01 How to Use This Manual
  • 2.02 Equipment Identification
  • 2.03 Receipt of Equipment
  • 2.04 Symbol Chart
  • 2.05 Description
  • 2.06 User Responsibility
  • 2.07 Packaged Items
  • 2.08 Duty Cycle
  • 2.09 WeldSkill 250 MIG Power Source Specifications
  • 2.10 WeldSkill 350 MIG Power Source Specifications
  • 2.11 WeldSkill 4R Wirefeeder Specifications
  • 2.12 Optional Accessories
• SECTION 3:INSTALLATION
  • 3.01 Environment
  • 3.02 Location
  • 3.03 Ventilation
  • 3.04 Mains Supply Voltage Requirements
  • 3.05 Installation and Users Responsibility
  • 3.06 Assessment of Area
  • 3.07 Methods of Reducing Electromagnetic Emissions
• SECTION 4:OPERATION
  • 4.01 Power Source Front Panel
  • 4.02 Power Source Internal Welding Controls
  • 4.03 4R Wirefeeder Front Panel
  • 4.04 Shielding Gas Regulator Operating Instructions
• SECTION 5:SET UP FOR THE WELDSKILL 250 & 350 POWER SOURCE
  • 5.01 Setup For The WeldSkill 250 & 350 MIG Power Source
  • 5.02 Wire Reel Brake
  • 5.03 Setup For The WeldSkill 250 & 350 MIG Power Source When Fitted With Wirefeeder
  • 5.04 Wire Reel Brake
• SECTION 6:BASIC WELDING GUIDE
  • 6.01 MIG (GMAW/FCAW) Basic Welding Technique
• SECTION 7:SERVICE
  • 7.01 Routine Service and Calibration Requirements
  • 7.02 Cleaning the Feed Rolls
  • 7.03 Basic Troubleshooting
  • 7.04 Solving Problems Beyond the Welding Terminals
  • 7.05 Solving Problems Beyond the Welding Terminals - Porosity
  • 7.06 Solving Problems Beyond the Welding Terminals – Inconsistent Wire Feed
  • 7.07 Welding Problems
  • 7.08 Power Source / Wirefeeder Problems
• APPENDIX 1:KEY SPARE PARTS
• APPENDIX 2:VOLT/AMP CURVES
• APPENDIX 3:WELDSKILL 250 MIG POWER SOURCE CIRCUIT DIAGRAM
• APPENDIX 4:WELDSKILL 350 MIG POWER SOURCE CIRCUIT DIAGRAM
• APPENDIX 5:4R WIREFEEDER CIRCUIT DIAGRAM
• CIGWELD LIMITED WARRANTY
• Terms of Warranty – January 2011
• Warranty Schedule – January 2011
• GLOBAL CUSTOMER SERVICE CONTACT INFORMATION
• APPENDIX 1: KEY SPARE PARTS
• APPENDIX 2: VOLT/AMP CURVES
• APPENDIX 3: WELDSKILL 250 MIG POWER SOURCE CIRCUIT DIAGRAM
• APPENDIX 4: WELDSKILL 350 MIG POWER SOURCE CIRCUIT DIAGRAM
• APPENDIX 5: 4R WIREFEEDER CIRCUIT DIAGRAM
• 0-5182-CIGWELD LIMITED WARRANTY
• 0-5182_APPX.pdf
  • APPENDIX 1: KEY SPARE PARTS
  • APPENDIX 2: VOLT/AMP CURVES
  • APPENDIX 3: WELDSKILL 250 MIG POWER SOURCE CIRCUIT DIAGRAM
  • APPENDIX 4: WELDSKILL 350 MIG POWER SOURCE CIRCUIT DIAGRAM
  • APPENDIX 5: 4R WIREFEEDER CIRCUIT DIAGRAM
• 0-5182_Ap.pdf
  • APPENDIX 1: KEY SPARE PARTS
  • APPENDIX 2: VOLT/AMP CURVES
  • APPENDIX 3: WELDSKILL 250 MIG POWER SOURCE CIRCUIT DIAGRAM
  • APPENDIX 4: WELDSKILL 350 MIG POWER SOURCE CIRCUIT DIAGRAM
  • APPENDIX 5: 4R WIREFEEDER CIRCUIT DIAGRAM
• 0-5182_Ap.pdf
  • APPENDIX 1: KEY SPARE PARTS
  • APPENDIX 2: VOLT/AMP CURVES
  • APPENDIX 3: WELDSKILL 250 MIG POWER SOURCE CIRCUIT DIAGRAM
  • APPENDIX 4: WELDSKILL 350 MIG POWER SOURCE CIRCUIT DIAGRAM
  • APPENDIX 5: 4R WIREFEEDER CIRCUIT DIAGRAM