Soleus GPS Sole (SG007) - Manual - Manual (Page 15)

RDY13
Setting ALARM:
Press S5 while ALARM is blinking. AL-1 will start to blink.
Press S1/S11 to toggle through Alarm 1 to alarm 5. The watch has 5 alarms which can
be set individually
Press S5 to set the selected Alarm number. The HOUR digit will start to blink.
Press S1/S11 to change the hour digit.
Press S5 to confirm and set the MINUTE digit. The minute digit starts to blink.
Press S1/S11 to change the minute digit.
Press S5 to confirm and set the T1 or T2 setting. T1 or T2 starts to blink. The alarm
time will be referred to Time 1 or Time 2.
Press S5 to confirm. Alarm ON or OFF will start to blink.
Press S1/S11 to change the setting.
Press S5 to confirm and go back to HOUR setting screen
Press S7 to exit to ALARM setting screen
Setting TIMER:
Press S5 while TMR is blinking. The segment number will start to blink.
Press S1/S11 to change the segment number
Press S5 to set the HOUR. The hour digit starts to blink.
Press S1/S11 to change the digits
Press S5 to set the MINUTE. The minute digit starts to blink.
Press S1/S11 to change the digits
Press S5 to set the SECONDS. The second digit starts to blink.
Press S1/S11 to zero the digits. If the value is more than 30 seconds, 1 minute will be
added to the minute digits
Press S5 to confirm and exit to TIMER setting screen.
In any Timer setting screen, press S7 will go to TIMER ALERT ON or OFF setting.
Setting the VIEW:
Press S5 while VIEW is blinking. The watch will display VIEW/DIST/ CHRONO.
CHRONO is blinking in line 3.
Press S1/S11 to change the information in line 3. You can select Chrono, Distance,
Pace, Speed, HRM, Calorie, or Clock.
Press S5 to enter. Line 2 will start to blink.
Press S1/S11 to change the information displayed in Line 2. You can select Chrono,
Distance, Pace, Speed, HRM, Calorie, or Clock.
Press S5 to go back to line 3 setting.
Press S7 to exit.
Battery:
Watch is using a rechargeable Lithium Ion battery that will require approximately 4-5 hours
charging time using the USB cable. While battery is charging, the watch cannot be used and
all buttons are disabled. User needs to recharge the battery when the watch indicates a
“LOW BATT”.
Note:
Battery Life (fully charge battery): 8 hrs typical of continuous run with GPS ON and CHRONO
ON.
Watch ttroubleshooting guide:
PROBLEM/ QUESTION SOLUTION/ ANSWER
I cannot get a GPS signal
Take your GPS watch outdoors and away from trees and
tall buildings. Remain stationary and try acquiring GPS
signal again. Be sure that the antenna is pointing towards
the sky for better signal reception.
Can I reset the watch?
You can reset the watch by pressing S1, S5, S7, and S11
together. The date and time will be reset to default
values. You can set it again manually or automatically thru
GPS.
Will my data and personal
settings be lost after watch
reset?
Your data and personal settings are saved in the flash
memory and will not be lost after watch reset.
The battery indicator does
not seem to be accurate
Allow your GPS watch to fully discharge and then fully
charge it without interruption. It is recommended to
regularly re-charge your battery every 1-2 months even if
it is not used to maintain good battery condition.
My heart rate data seems
inaccurate.
- Make sure the HR belt is snugly fit to your body
- Reapply water or electrode gel to the electrode of the
HR belt
- Clean the electrodes from possible contamination that
may interfere with heart rate signals
- Wear a cotton shirt or if possible, wet your cotton shirt.
Synthetic fabrics that rubs with your skin may create
static electricity and interfere with the heart rate signal
- Move away from strong electromagnetic fields and other
wireless sensors which can interfere with your heart rate
sensor. Possible sources of wireless interference may
include high voltage power lines, electric motors,
microwave ovens, cordless phones, and wireless LAN
or access points.
GPS Sole