Rockwell Automation 2711-KA1_KC1_TA1_TA4_TC1_TC4 PanelView Terminals for DOS/Windows - Manual (Page 92)

Troubleshooting
Appendix B
B-2
The following table lists the most common minor fault messages that can
appear on a PanelView 1200 terminal.
Minor Fault Message Cause What to do
Retentive data initialization failed. There is no valid application file. Go offĆline and download the file again.
Audio hardware initialization failed. There is an audio hardware problem. Servicing by AllenĆBradley is required.
Terminal can't keep up with activity. Too much incoming data. The operator should stop all input until the
PanelView 1200 terminal can process data.
Invalid Powerup Screen. Powerup screen does not exist or is faulty. Reassign the Powerup Screen or check the
configuration data in the PanelBuilder
application file.
ББББББББББББ
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
ББББББББББББ
User EPROM/EEPROM is not installed or is
corrupted.
ББББББББББББ
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
ББББББББББББ
Optional EPROM or EEPROM was not found or
is faulty.
ББББББББББББ
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
ББББББББББББ
If no user EPROM or EEPROM is installed,
ignore this message. You can disable the test
and the message in the Configuration Mode
Menu.
If a user EPROM or EEPROM is installed, check
PROM jumpers, look for bent pins, check for
proper PROM notch alignment, and verify that
there is a valid program in the PROM. If the
PROM is an EEPROM, try downloading the
application file again.
ББББББББББББ
Б ББББББББББ Б
ББББББББББББ
Battery test failed. User RAM will be lost on
power down.
ББББББББББББ
Б ББББББББББ Б
ББББББББББББ
The battery for application file memory is dead.
ББББББББББББ
Б ББББББББББ Б
ББББББББББББ
Upload the application file and save it on disk.
Servicing by AllenĆBradley is required.
ББББББББББББ
ББББББББББББ
Communication Self Test failed.
ББББББББББББ
ББББББББББББ
The communication card is defective or not
installed. ББББББББББББ
ББББББББББББ
Servicing by AllenĆBradley is required.
ББББББББББББ
Б ББББББББББ Б
ББББББББББББ
Invalid Screen. ББББББББББББ
Б ББББББББББ Б
ББББББББББББ
The PLC has selected a nonĆexistent screen
number.
ББББББББББББ
Б ББББББББББ Б
ББББББББББББ
Reprogram the PLC or the application file.
ББББББББББББ
Б ББББББББББ Б
ББББББББББББ
Unable to write downloaded data to the
EEPROM.
ББББББББББББ
Б ББББББББББ Б
ББББББББББББ
The EEPROM is faulty or user memory
configuration jumpers are set incorrectly.
ББББББББББББ
Б ББББББББББ Б
ББББББББББББ
Check the EEPROM, and verify user memory
configuration jumper settings.
ББББББББББББ
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
ББББББББББББ
Value Out Of Range.
ББББББББББББ
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
ББББББББББББ
Address not sufficient for data transfer.
Current screen number transferred to PLC is not
sufficient.
Numeric entry or display address length is
insufficient for data.
ББББББББББББ
Б ББББББББББ Б
Б ББББББББББ Б
Б ББББББББББ Б
ББББББББББББ
Increase bit length of address so it's large
enough for screen transfer, including Alarm
History and Alarm Status screens.
Increase address length for data.
PLC currently controls screen change PLC controller has control of screen change. Disable PLC Controlled Screen Change.
Set PLC Controlled Screen Change value to 0.
No screen changeĊHold Time in effect or no
PLC Handshake
Operator is trying to change screens while a
button's hold time is still in effect or before an
activated Latched Push Button has received a
handshake.
Wait until hold time is finished or Latched
handshake is received before trying to change
screens.
PanelView 1200 Minor Fault
Error Messages