Despatch Protocol 3 Modbus Communications User Manual
Ultraflex drying and firing furnace, Owners manual, Modbus user’s programming manual for protocol 3
Table of contents
Document Outline
- 1. About This Manual
- 1.1. Important User Information
- 1.2. Manufacturer & Service
- 1.3. Organization of this Manual
- 1.3.1. Reference Documents
- 1.4. Serial Communications
- 1.4.1. Supported Protocols
- 1.4.2. RS485 Configuration
- 1.4.3. RS485 Device Addressing
- 1.4.4. Ethernet Configuration
- 1.4.5. Link Layer
- 1.4.6. Supported Modbus Functions
- 1.4.7. Function Descriptions
- 1.4.8. Data Formats
- 2. Modbus Address List
- 2.1. Input Parameters
- 2.1.1. Process Input Parameters
- 2.1.2. High Limit Input Parameters
- 2.1.3. Digital Inputs
- 2.2. Output Parameters
- 2.2.1. Relay Output 1 Parameters
- 2.2.2. Relay Output 2 Parameters
- 2.2.3. Relay Output 3 Parameters
- 2.2.4. Relay Output 4 Parameters
- 2.2.5. Relay Output 5 Parameters
- 2.2.6. Linear Output Parameters
- 2.3. Setpoint Parameters
- 2.4. Control Parameters
- 2.5. Alarm Parameters
- 2.5.1. Alarm 1
- 2.5.2. Alarm 2
- 2.5.3. Alarm 3
- 2.5.4. Alarm 4
- 2.5.5. Alarm 5
- 2.5.6. High Limit Alarm Parameters
- 2.6. Logger parameters (Data Logger)
- 2.6.1. Data Recorder
- 2.6.2. Real Time Clock
- 2.7. Display Parameters
- 2.7.1. Keys
- 2.7.2. LEDs
- 2.7.3. HMI
- 2.7.4. System Data
- 2.8. Mode Controls
- 2.8.1. General Mode Control
- 2.8.2. Manual Mode Parameters
- 2.8.3. Timer Mode Parameters
- 2.8.4. Profile Mode Parameters
- 2.9. Uploading and Downloading of Profiles
- 2.9.1. Instruction Sequence to create a profile at the next available position
- 2.9.2. Instruction Sequence to create a profile at a specified profile position
- 2.9.3. Instruction Sequence to edit an existing Profile Header
- 2.9.4. Instruction Sequence to read a profile
- 2.9.5. Profile Command Code Descriptions
- 2.9.5.1. Creating a profile header (Command Code CP)
- 2.9.5.2. Editing/Creating a profile header at a location (Command Code EP or WP)
- 2.9.5.3. Creating a Segment (Command Code WS)
- 2.9.5.4. Editing or Inserting a Segment (Command Codes IS and ES)
- 2.9.5.5. Segment Info A, B Information
- 2.9.5.6. Deleting Profiles (Command Code DP and DA)
- 2.9.5.7. Deleting a Segment (Command Code DS)
- 2.9.5.8. Getting the Number of Segments Remaining (Command Code SR)
- 2.9.5.9. Edit Response Message
- 2.9.5.10. Reading a Profile Header (Command Code RP)
- 2.9.5.11. Read a Segment (Command Code RS)
- 2.9.5.12. Read a profile Name (Command Code PN)
- 2.9.5.13. Read Profile Memory Status (Command Code PS)