Class1 3041-10X-00-CL1 - Sentry Governor - EXTERNAL User Manual
Technical product datasheet, Sentry pressure governor with twister control
Table of contents
Document Outline
- Revision Log
- 2. System Overview
- 3. Overview of the Sentry Governor
- 3.1. Mode and Interlock indicators (Sentry)
- 3.2. Pump discharge pressure display (Sentry)
- 3.3. Pump intake pressure display (Sentry)
- 3.4. Mode, Preset, and Idle buttons (Sentry)
- 3.5. “Soft” buttons (Sentry)
- 3.6. Information displays (Sentry)
- 3.7. Ready indicator (Twister)
- 3.8. Active indicator (Twister)
- 3.9. Control knob (Twister)
- 3.10. Idle button (Twister)
- 4. Operation
- 5. Warning and Error messages
- 5.1. First level message information (operator)
- 5.2. Second level message information (technician)
- 5.3. List of warning/error messages
- 5.3.1. Intake or Discharge Sensor Fault
- 5.3.2. Water Supply Insufficient, Discharge Pressure Less Than 30 Psi, and Critical: Sentry In Stand By. Check Water Source
- 5.3.3. Unable To Maintain Discharge Pressure
- 5.3.4. Discharge Pressure Has Increased More Than 50 Psi Since Setting Rpms
- 5.3.5. Communication with engine is lost
- 6. Sentry Setup Menus
- 6.1. Engine compatibility
- 6.2. Enter the setup menu
- 6.3. INFO menu
- 6.4. USER menu
- 6.4.1. Change the unit of measure
- 6.4.2. Change the Preset RPM 1
- 6.4.3. Change the Preset Pressure 1
- 6.4.4. Change the Preset RPM 2
- 6.4.5. Change the Preset Pressure 2
- 6.4.6. Change the Display Brightness (day mode)
- 6.4.7. Change the Display Brightness (night mode)
- 6.4.8. Round pressure
- 6.4.9. Change the Display Mode (Day or Night)
- 6.5. OEM 1 menu
- 6.5.1. Set the Warning Alert Tone
- 6.5.2. Sensitivity (pressure)
- 6.5.3. First Operating Mode
- 6.5.4. Intake Sensor Range
- 6.5.5. Discharge Sensor Range
- 6.5.6. Inhibit RPM Presets
- 6.5.7. Warning Source
- 6.5.8. Coolant Temperature Warning (USER)
- 6.5.9. Coolant Temperature Critical (USER)
- 6.5.10. Oil Pressure Warning (USER)
- 6.5.11. Oil Pressure Critical (USER)
- 6.5.12. Intake Threshold
- 6.6. OEM 2 menu
- 6.6.1. Battery Voltage Range
- 6.6.2. Engine Control Method
- 6.6.3. Auto Mode
- 6.6.4. Idle Voltage
- 6.6.5. Idle Engine Speed (RPM)
- 6.6.6. Maximum Engine Speed (RPM)
- 6.6.7. CAN Source ID
- 6.6.8. Pressure Time-Out (Seconds)
- 6.6.9. Governor Gain (RPM per volt)
- 6.6.10. Pressure Gain (pressure change per step)
- 6.6.11. DITHER (Engine handshake)
- 6.6.12. LAG (PSI/kPa/Bar)
- 6.6.13. BCM1 VER (Body Control Message 1 version)
- 6.6.14. Scania Mode (Scania governor type)
- 6.7. FACT menu
- 7. Configuration
- 8. Mounting & installation
- 9. Connector Description
- 10. Technical Details