Technical data sheet – Class1 117155 - TPG Governor - 117684 EXTERNAL User Manual
Page 3
FORM-ENG-0018 REV A 05-27-03
607 NW 27th Ave
Ocala, FL 34475
Ph: 352-629-5020 or 1-800-533-3569
Fax : 352-629-2902 or 1-800-520-3473
TECHNICAL DATA SHEET
PAGE
2
OF 26
DATE
3/28/2012
PRODUCT GROUP
THROTTLE CONTROL
P/N
117155
REV
1.23
PRODUCT
TOTAL PRESSURE GOVERNOR (TPG)
BY
AMS
Manual P/N 117684
5.2.19.
DISPLAY (primary display in pressure mode) ............................................................................ 18
5.2.20.
PSI TIME-OUT (pressure time out) ............................................................................................. 18
5.2.21.
ALLOW PRESET (allow RPM preset use when pressure is detected) ...................................... 18
5.2.22.
WARNINGS (data monitor warning configuration) ..................................................................... 19
A.
WARN ºF (User defined engine temperature high warning - Yellow LED).......................................................19
B.
CRIT ºF (User defined engine temperature high critical - Red LED) ...............................................................19
C.
WARN PSI (User defined oil pressure low warning - Yellow LED) ..................................................................19
D.
CRIT PSI (User defined oil pressure low critical - Red LED) ...........................................................................19
5.2.23.
XDUCR (discharge pressure transducer range) ......................................................................... 19
5.2.24.
FACTORY DFLT (Set factory defaults) ....................................................................................... 19
5.2.25.
POC ASSERT (Power On Cycle assertion) ................................................................................ 19
5.2.26.
GOV GAIN (RPM change per step) ............................................................................................ 19
5.2.27.
PRESS GAIN (PSI change per step) .......................................................................................... 19
5.2.28.
DITHER (Engine handshake)...................................................................................................... 20
5.2.29.
LAG
∆PSI (Pressure lag) ............................................................................................................ 20
5.2.30.
PUMP HOURS ............................................................................................................................ 20
5.2.31.
BCM1 VER (Body Control Message 1 version) .......................................................................... 20
5.2.32.
SCANIA MODE? (Scania governor type) ................................................................................... 20
5.2.33.
IDLE STEPS (Analog control idle) .............................................................................................. 20
5.2.34.
OKAY2PUMP (Okay to pump interlock source).......................................................................... 20
5.2.35.
SPN 3350 (TSC1 – SPN 3350) ................................................................................................... 21
5.2.36.
SPN 696 (Engine Requested Speed Control Condition) ............................................................ 21
5.2.37.
HI IDLE MODE ............................................................................................................................ 21
5.2.38.
BUS INTLKS (Bus message control of throttle ready interlock) ................................................. 21
5.2.39.
VOLTS (Voltage display calibration) ........................................................................................... 21
5.2.40.
SMOOTHING (Pressure display averaging) ............................................................................... 21
5.2.41.
ENGINE ID (Source ID of received engine messages) .............................................................. 22
6.
SPECIAL FUNCTION PASSWORDS (SEE SECTION 5.2 FOR PROCEDURE ON ENTERING
PASSWORDS) ...................................................................................................................................................... 23
6.1.
S
ETTING CONTROL MESSAGE TRANSMISSION REQUIREMENTS
................................................................... 23
6.2.
S
ETTING CONTROL FOR SPECIFIC ENGINE TYPES
...................................................................................... 23
6.3.
C
ONFIGURING TRANSMISSION OF
H
YDRAULIC
P
RESSURE
G
OVERNOR MESSAGE
........................................ 23
7.
CONFIGURATION ..................................................................................................................................... 24
7.1.
C
ONFIGURE THE UNIT OF MEASURE
......................................................................................................... 24
7.2.
S
ELECT PRESSURE TRANSDUCER RANGE
(300
PSI,
600
PSI) .................................................................. 24
7.3.
Z
ERO CALIBRATE THE PRESSURE TRANSDUCER
....................................................................................... 25
7.4.
C
ONFIGURE THE ENGINE CONTROL METHOD
............................................................................................ 25
7.5.
C
ONFIGURE THE
IDLE
VOLTAGE AND
GAIN
SETTING USING
A
UTO
S
CALE
................................................. 26
8.
MOUNTING & INSTALLATION ................................................................................................................. 27
8.1.
P
ANEL CUTOUT DIMENSIONS
................................................................................................................... 27
9.
CONNECTOR DESCRIPTION................................................................................................................... 28
9.1.
TPG
CONNECTORS
................................................................................................................................ 28
9.2.
P
RESSURE SENSOR CONNECTOR
............................................................................................................ 28
10.
MODULE OPERATING PARAMETERS ................................................................................................... 29