AEM Infinity Supported Applications - Universal V8 Engine - Manual (Page 42)

42
© 2014 AEM Performance Electronics
Infinity
Pin
Hardware Ref.
7100-XXXX-62
7101-XXXX-63
Function
Hardware Specification Notes
C2-8 Power Ground* Ground Power Ground
Connect directly to battery ground. *Pin
not populated in 30-3805 Univ ersal V8
Base harness.
C2-9 +12V +12V In 12 v olt power f rom relay
12 v olt power f rom relay . Relay must be
controlled by +12V Relay Control signal,
pin C1-29 abov e.
C2-10 Injector 11 Injector 11
Saturated or peak and hold, 3A max
continuous
Not used
C2-11 Injector 12 Injector 12
Saturated or peak and hold, 3A max
continuous
Not used
C2-12 Analog_In_17
Spare Analog
Input
12 bit A/D, 100K pullup to 5V
0–5V analog signal. Use +5V Out pins as
power supply and Sensor Ground pins as
the low ref erence. Do not connect signals
ref erenced to +12V as this can
permanently damage the ECU. Normally
used as A/C Analog Request input.
C2-13 Analog_In_18*
Spare Analog
Input
12 bit A/D, 100K pullup to 5V
0–5V analog signal. Use +5V Out pins as
power supply and Sensor Ground pins as
the low ref erence. Do not connect signals
ref erenced to +12V as this can
permanently damage the ECU. Normally
used as DBW APP1. *Pin not populated in
30-3805 Univ ersal V8 Base harness.
C2-14 Analog_In_19*
Spare Analog
Input
12 bit A/D, 100K pullup to 5V
0–5V analog signal. Use +5V Out pins as
power supply and Sensor Ground pins as
the low ref erence. Do not connect signals
ref erenced to +12V as this can
permanently damage the ECU. Normally
used as DBW APP2. *Pin not populated in
30-3805 Univ ersal V8 Base harness.
C2-15 Analog_In_Temp_4*
Spare Temp
Input
12 bit A/D, 2.49K pullup to 5V
Normally used as Charge Out
Temperature input. *Pin not populated in
30-3805 Univ ersal V8 Base harness.
C2-16 Analog_In_Temp_5*
Spare Temp
Input
12 bit A/D, 2.49K pullup to 5V
Normally used as Airbox Temperature
input. *Pin not populated in 30-3805
Univ ersal V8 Base harness.
C2-17 Analog_In_Temp_6*
Spare Temp
Input
12 bit A/D, 2.49K pullup to 5V
Normally used as Fuel Temperature input.
*Pin not populated in 30-3805 Univ ersal
V8 Base harness.
C2-18 Analog_In_13 Oil Pressure 12 bit A/D, 100K pullup to 5V
0–5V analog signal. Use +5V Out pins as
power supply and Sensor Ground pins as
the low ref erence. Do not connect signals
ref erenced to +12V as this can
permanently damage the ECU. See
Setup Wizard Oil Pressure page f or setup
options. See OilPressure [psig] f or
channel data.
C2-19 Analog_In_14
Spare Analog
Input
12 bit A/D, 100K pullup to 5V
0–5V analog signal. Use +5V Out pins as
power supply and Sensor Ground pins as
the low ref erence. Do not connect signals
ref erenced to +12V as this can
permanently damage the ECU.