AEM Infinity Supported Applications - Universal V8 Engine - Manual (Page 41)

Universal 8 41
© 2014 AEM Performance Electronics
Infinity
Pin
Hardware Ref.
7100-XXXX-62
7101-XXXX-63
Function
Hardware Specification Notes
C1-61 +12V +12V In 12 v olt power f rom relay
12 v olt power f rom relay . Relay must be
controlled by +12V Relay Control signal,
pin C1-29 abov e.
C1-62 Injector 2 Injector 2
Saturated or peak and hold, 3A max
continuous
Injector 2
C1-63 Injector 1 Injector 1
Saturated or peak and hold, 3A max
continuous
Injector 1
C1-64 +12V +12V In 12 v olt power f rom relay
12 v olt power f rom relay . Relay must be
controlled by +12V Relay Control signal
pin C1-29 abov e.
C1-65 +12V_SW Ignition Switch 10K pulldown
Full time battery power must be av ailable
at C1-10 bef ore this input is triggered.
C1-66 Analog_In_Temp_1
Coolant Temp
Sensor
12 bit A/D, 2.49K pullup to 5V
See "Coolant Temperature" Setup Wizard
f or selection.
C1-67 Analog_In_Temp_2
Intake Air
Temperature
12 bit A/D, 2.49K pullup to 5V
See "Air Temperature" Setup Wizard f or
selection.
C1-68 Analog_In_Temp_3*
Spare Temp
Input
12 bit A/D, 2.49K pullup to 5V
Normally used f or Oil Temp input. *Pin
not populated in 30-3805 Univ ersal V8
Base harness.
C1-69 Stepper_2A Stepper 2A
Automotiv e, Programmable Stepper
Driv er, up to 28V and ±1.4A
Be sure that each internal coil of the
stepper motor are properly paired with the
1A/1B and 2A/2B ECU outputs. Supports
Bi-Polar stepper motors only .
C1-70 Stepper_1A Stepper 1A
Automotiv e, Programmable Stepper
Driv er, up to 28V and ±1.4A
Be sure that each internal coil of the
stepper motor are properly paired with the
1A/1B and 2A/2B ECU outputs. Supports
Bi-Polar stepper motors only .
C1-71 Stepper_2B Stepper 2B
Automotiv e, Programmable Stepper
Driv er, up to 28V and ±1.4A
Be sure that each internal coil of the
stepper motor are properly paired with the
1A/1B and 2A/2B ECU outputs. Supports
Bi-Polar stepper motors only .
C1-72 Stepper_1B Stepper 1B
Automotiv e, Programmable Stepper
Driv er, up to 28V and ±1.4A
Be sure that each internal coil of the
stepper motor are properly paired with the
1A/1B and 2A/2B ECU outputs. Supports
Bi-Polar stepper motors only .
C1-73 Power Ground Ground Power Ground Connect directly to battery ground
C2-1 DBW2 Motor +*
DBW Motor
Control Open
5.0A max Throttle Control Hbridge Driv e
+12V to open. *Pin not populated in 30-
3805 Univ ersal V8 Base harness.
C2-2 DBW2 Motor -*
DBW Motor
Control Close
5.0A max Throttle Control Hbridge Driv e
+12V to close. *Pin not populated in 30-
3805 Univ ersal V8 Base harness.
C2-3 Power Ground Ground Power Ground Connect directly to battery ground
C2-4 Injector 7 Injector 7
Saturated or peak and hold, 3A max
continuous
Injector 7
C2-5 Injector 8 Injector 8
Saturated or peak and hold, 3A max
continuous
Injector 8
C2-6 Injector 9* Injector 9
Saturated or peak and hold, 3A max
continuous Injector 9. *Pin not populated in 30-3805
Univ ersal V8 Base harness.
C2-7 Injector 10* Injector 10
Saturated or peak and hold, 3A max
continuous Injector 10. *Pin not populated in 30-3805
Univ ersal V8 Base harness.