AEM 30-2340-N 4-Channel Wideband UEGO AFR Controller - For use with Nascar McLaren ECU User Manual
Page 21
Page 21
3 (bit2)
AFR 8 VM Error
Boolean
0 = false, 1 = true
0
0/1
3 (bit3)
AFR 8 UN Error
Boolean
0 = false, 1 = true
0
0/1
3 (bit4)
AFR 8 IP Error
Boolean
0 = false, 1 = true
0
0/1
3 (bit5)
AFR 8 Heater Time-Out Error
Boolean
0 = false, 1 = true
0
0/1
3 (bit6)
AFR 8 Heater Short Error
Boolean
0 = false, 1 = true
0
0/1
3 (bit7)
AFR 8 Overtemp Error
Boolean
0 = false, 1 = true
0
0/1
4 (bit0)
UEGO Low Voltage Error
Boolean
0 = false, 1 = true
0
0/1
4 (bit1)
EBP sensor ready
Boolean
0 = false, 1 = true
0
0/1
4 (bit2)
EBP sensor Error Low Volt
Boolean
0 = false, 1 = true
0
0/1
4 (bit3)
EBP sensor detected
Boolean
0 = false, 1 = true
0
0/1
4 (bit4)
CAN Config Mode
Boolean
0 = false, 1 = true
0
0/1
4 (bit5)
CAN Config Mode
Boolean
0 = false, 1 = true
0
0/1
4 (bit6)
CAN Config Mode
Boolean
0 = false, 1 = true
0
0/1
4 (bit7)
CAN Config Mode
Boolean
0 = false, 1 = true
0
0/1
5 (bit0)
Reserved
Boolean
0 = false, 1 = true
0
0/1
5 (bit1)
Reserved
Boolean
0 = false, 1 = true
0
0/1
5 (bit2)
Reserved
Boolean
0 = false, 1 = true
0
0/1
5 (bit3)
Reserved
Boolean
0 = false, 1 = true
0
0/1
5 (bit4)
Sensor 8 Heating up
Boolean
0 = false, 1 = true
0
0/1
5 (bit5)
Sensor 7 Heating up
Boolean
0 = false, 1 = true
0
0/1
5 (bit6)
Sensor 6 Heating up
Boolean
0 = false, 1 = true
0
0/1
5 (bit7)
Sensor 5 Heating up
Boolean
0 = false, 1 = true
0
0/1
6
Exhaust Pressure 2
16 bit unsigned
.001 psig/bit
0
0 to 655.35 psig
7
Message ID:
0x000001B1
Source:
AEM 4 Channel UEGO set on MODE 3
Rate: 40ms
continuous
Byte
Label
Data Type
Scaling
Offset
Range
0 (bit0)
AFR 1 Ready
Boolean
0 = false, 1 = true
0
0/1
0 (bit1)
AFR 1 Heater Open Error
Boolean
0 = false, 1 = true
0
0/1
0 (bit2)
AFR 1 VM Error
Boolean
0 = false, 1 = true
0
0/1
0 (bit3)
AFR 1 UN Error
Boolean
0 = false, 1 = true
0
0/1
0 (bit4)
AFR 1 IP Error
Boolean
0 = false, 1 = true
0
0/1
0 (bit5)
AFR 1 Heater Time-Out Error
Boolean
0 = false, 1 = true
0
0/1
0 (bit6)
AFR 1 Heater Short Error
Boolean
0 = false, 1 = true
0
0/1
0 (bit7)
AFR 1 Overtemp Error
Boolean
0 = false, 1 = true
0
0/1
1 (bit0)
AFR 3 Ready
Boolean
0 = false, 1 = true
0
0/1
1 (bit1)
AFR 3 Heater Open Error
Boolean
0 = false, 1 = true
0
0/1
1 (bit2)
AFR 3 VM Error
Boolean
0 = false, 1 = true
0
0/1
1 (bit3)
AFR 3 UN Error
Boolean
0 = false, 1 = true
0
0/1
1 (bit4)
AFR 3 IP Error
Boolean
0 = false, 1 = true
0
0/1
1 (bit5)
AFR 3 Heater Time-Out Error
Boolean
0 = false, 1 = true
0
0/1
1 (bit6)
AFR 3 Heater Short Error
Boolean
0 = false, 1 = true
0
0/1
1 (bit7)
AFR 3 Overtemp Error
Boolean
0 = false, 1 = true
0
0/1
2 (bit0)
AFR 5 Ready
Boolean
0 = false, 1 = true
0
0/1