HP ROM-Based Setup Utility User Manual
Hp rom-based setup utility user guide
Table of contents
Document Outline
- HP ROM-Based Setup Utility User Guide
- Contents
- 1 Introduction
- 2 RBSU menu-driven interface, version 3.xx or later (G6, G7, and Gen8 servers)
- RBSU main menu
- System Options menu
- Serial Port options
- Embedded NICs
- NIC Personality Options
- Advanced Memory Protection
- USB Options
- Processor Options
- No-Execute Memory Protection
- No-Execute Page Protection
- Intel Virtualization Technology
- AMD V (AMD Virtualization)
- Intel Hyperthreading Options
- Enhanced Processor Core Disable (Intel Core Select)
- Processor Core Disable (Intel Core Select) (G7 and Gen8 servers)
- Processor Core Disable (AMD Core Select)
- Intel Turbo Boost Technology
- Intel Turbo Boost Technology (Gen8 servers)
- Intel Turbo Boost Technology (G7 servers)
- AMD Core Performance Boost
- Intel VT-d
- AMD-Vi (IOMMU)
- Remote Console Mode
- NUMLOCK Power-On State
- SATA Controller Options (Gen8 servers with SATA controllers)
- Power Management Options menu
- HP Power Profile
- HP Power Regulator
- Redundant Power Supply Mode
- Advanced Power Management Options
- Intel QPI Link Power Management
- Intel QPI Link Frequency
- QPI Bandwidth Optimization (RTID)
- Minimum Processor Idle Power Core State
- Minimum Processor Idle Power Core C6 State
- Minimum Processor Idle Power C1e State
- Minimum Processor Idle Power Package State
- Minimum Processor Idle Power State
- Energy/Performance Bias
- Maximum Memory Bus Frequency
- Channel Interleaving
- Memory Interleaving
- PCI Express Generation 2.0 Support
- PCIe Gen 3 Control (for select devices)
- Maximum PCI Express Speed
- Dynamic Power Savings Mode Response
- Collaborative Power Control
- Power Capping Support
- ACPI SLIT Preferences
- DIMM Idle Power Saving Mode
- DIMM Voltage Preference
- Memory Power Savings Mode
- HyperTransport Frequency
- Dynamic Power Capping Functionality
- PCI IRQ Settings menu
- PCI Device Enable/Disable menu
- Standard Boot Order (IPL) menu
- Boot Controller Order menu
- Date and Time menu
- Server Availability menu
- Server Security menu
- BIOS Serial Console & EMS menu
- Server Asset Text menu
- Advanced Options menu
- Advanced System ROM Options
- Option ROM Loading Sequence
- MPS Table Mode
- ROM Selection
- NMI Debug Button
- Virtual Install Disk
- PCI Bus Padding Options
- Memory Mapped I/O Options
- Address Mode 44-bit
- Power-On Logo
- F11 Boot Menu Prompt
- Consistent Device Naming
- Network Boot Retry Support
- Hide Option ROM Messages
- PCIe Slot6 Training Speed
- Reset on Boot Device Not Found
- HP Option ROM Prompting
- Video Options
- Power Supply Requirements Override
- Thermal Configuration
- Service Options
- Advanced Performance Tuning Options
- HW Prefetcher
- Adjacent Sector Prefetch
- DCU Prefetcher
- DCU Streamer Prefetcher
- DCU IP Prefetcher
- Data Reuse
- Hardware Prefetch training on Software Prefetch
- DRAM Prefetch on CPU Request
- DRAM Prefetch on I/O Request
- CPU Core Hardware Prefetcher
- CPU Cache Stride Prefetcher
- Stack Engine Prediction
- Node Interleaving
- 1333 MHz Support for 3DPC-10600H HP SmartMemory
- Data Direct I/O
- Memory Channel Mode
- Memory Speed with 2 DIMMs per Channel
- Hemisphere Mode
- HPC Optimization Mode
- ACPI SLIT Preferences
- Intel Performance Counter Monitor (PCM)
- One Terabyte Memory Limit
- Drive Write Cache
- Asset Tag Protection
- SR-IOV
- Embedded SATA RAID
- Advanced System ROM Options
- System Default Options menu
- Utility Language menu (G5 through G7 servers)
- Utility Language menu (Gen8 servers)
- 3 RBSU menu-driven interface, version 2.xx (G5 and earlier servers)
- RBSU main menu
- System Options menu
- Embedded Serial Port A
- Embedded Serial Port B
- Virtual Serial Port
- Optional LPT Mode Support
- Integrated Diskette Controller
- NUMLOCK Power-On State
- Embedded NICs
- Diskette Write Control
- Diskette Boot Control
- Advanced Memory Protection
- USB Control
- USB 2.0 EHCI Controller
- Power Regulator for ProLiant
- USB External Port Capability
- Ultra Low Power State
- PCI Devices menu
- Standard Boot Order (IPL) menu
- Boot Controller Order menu
- Date and Time menu
- Server Availability menu
- Server Passwords menu
- BIOS Serial Console and EMS menu
- Server Asset Text menu
- Advanced Options menu
- Multi-Processor Specification (MPS) Table Mode
- ROM Selection
- Restore Default System Settings
- Restore Settings/Erase Boot Disk
- User Default Options
- NMI Debug Button
- Virtual Install Disk
- Secondary IDE Channel Support
- BIOS Enhanced RAID
- Node Interleaving
- Serial Number
- Product ID
- Drive Write Cache
- SATA Software RAID
- Optional PCI-X Riser Fan Monitoring
- Processor Options
- Power Supply Requirements Override
- Embedded VGA Control
- Utility Language menu
- 4 RBSU BIOS Serial Console (CLI)
- 5 RBSU configuration flows (manual and scripted)
- 6 ROM-based utilities
- 7 Support and other resources
- 8 Documentation feedback
- Acronyms and abbreviations
- Index