beautypg.com

Serial ata hard disk drive connection, Utility embedded on the intel, Ich7r southbridge – Asus TS300-E3 User Manual

Page 79

background image

4 - 1 1

4 - 1 1

4 - 1 1

4 - 1 1

4 - 1 1

A S U S T S 3 0 0 - E 3

A S U S T S 3 0 0 - E 3

A S U S T S 3 0 0 - E 3

A S U S T S 3 0 0 - E 3

A S U S T S 3 0 0 - E 3

3 .

3 .

3 .

3 .

3 .

Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)

Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)

Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)

Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)

Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)

These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.

If you installed Serial ATA hard disk drives, you can create a RAID 0,
RAID 1, RAID 0+1, and software RAID 5 configuration using the Intel

®

Matrix Storage Technology or RAID 0, RAID 1 and RAID 0+1
configuration using the LSI MegaRAID

®

utility embedded on the Intel

®

ICH7R Southbridge.

Serial ATA hard disk drive connection

Serial ATA hard disk drive connection

Serial ATA hard disk drive connection

Serial ATA hard disk drive connection

Serial ATA hard disk drive connection

C o n n e c t o r

C o n n e c t o r

C o n n e c t o r

C o n n e c t o r

C o n n e c t o r

S e t t i n g

S e t t i n g

S e t t i n g

S e t t i n g

S e t t i n g

U s e

U s e

U s e

U s e

U s e

S A T A 1 / S A T A 2

S A T A 1 / S A T A 2

S A T A 1 / S A T A 2

S A T A 1 / S A T A 2

S A T A 1 / S A T A 2

M a s t e r

M a s t e r

M a s t e r

M a s t e r

M a s t e r

B o o t d i s k

B o o t d i s k

B o o t d i s k

B o o t d i s k

B o o t d i s k

S A T A 3 / S A T A 4

S A T A 3 / S A T A 4

S A T A 3 / S A T A 4

S A T A 3 / S A T A 4

S A T A 3 / S A T A 4

S l a v e

S l a v e

S l a v e

S l a v e

S l a v e

D a t a d i s k

D a t a d i s k

D a t a d i s k

D a t a d i s k

D a t a d i s k

These connectors are set I D E

I D E

I D E

I D E

I D E mode by default. In I D E

I D E

I D E

I D E

I D E mode, you can

connect Serial ATA boot/data hard disk drives to these connectors. If
you intend to create a Serial ATA RAID set using these connectors, set
the C o n f i g u r e S A T A a s

C o n f i g u r e S A T A a s

C o n f i g u r e S A T A a s

C o n f i g u r e S A T A a s

C o n f i g u r e S A T A a s item in the BIOS to [RAID]. See section

“4.3.4 IDE Configuration” for details.

I m p o r t a n t n o t e s o n S e r i a l A T A

I m p o r t a n t n o t e s o n S e r i a l A T A

I m p o r t a n t n o t e s o n S e r i a l A T A

I m p o r t a n t n o t e s o n S e r i a l A T A

I m p o r t a n t n o t e s o n S e r i a l A T A

You must install Windows

®

2000 Service Pack 4 or Windows

®

2003

before using Serial ATA hard disk drives. The Serial ATA RAID
feature (RAID 0/RAID 1) is available only if you are using Windows

®

2000/2003.

Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1
set.

When using the connectors in I D E

I D E

I D E

I D E

I D E mode, connect the primary (boot)

hard disk drive to the SATA1 or SATA2 connector. Refer to the table
below for the recommended SATA hard disk drive connections.

LAN2

®

P5MT Series SATA connectors

SATA2

GND

RSATA_TXP2
RSATA_TXN2

GND

RSATA_RXP2
RSATA_RXN2

GND

SATA1

GND

RSATA_TXP1
RSATA_TXN1

GND

RSATA_RXP1
RSATA_RXN1

GND

SATA4

GND

RSATA_TXP4
RSATA_TXN4

GND

RSATA_RXP4
RSATA_RXN4

GND

SATA3

GND

RSATA_TXP3
RSATA_TXN3

GND

RSATA_RXP3
RSATA_RXN3

GND

This manual is related to the following products: